manualshive.com logo in svg

Raycus RFL-C4000S, Руководство пользователя

Поделиться
Скачать
Raycus RFL-C4000S Скачать руководство пользователя страница 26

26 

 

Figure 10 The 

clientware interface

 

4.7.1 

The control interface

 

The control interface is the content displayed on the first page after opening the clientware, 

including the user's most commonly used status signal, laser parameter setting and laser control 

related functions. 

Control the main power: turn on or off the main power. After turning on or off the main power, 

the software will change the status of the main power. 

Control abnormal laser reset: Click the reset button to run the abnormal laser reset command. 

Guide laser: the guide laser is turned on or off in the internal control state of guide laser. After 

the guide laser is turned on or off, there will be changes in the guide laser state on the software. 

Guide laser external control: turn on the guide laser external control or turn off the guide laser 

external control. After turning on and turn off the guide laser external control, there will be changes 

of the guide laser external control state in the software.

 

If the current red external control state, 

then disable the red control button. 

Read and set the parameters of rise time and fall time: The rise time and fall time can be set 

separately and must be an integer ranging from 0 to 61000.

 

Содержание RFL-C4000S










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды