Ravenheat RSF 84E Скачать руководство пользователя

Страница: 50 / 55

90” M/F bend consisting of:

90” elbow with ‘0’ ring side F
80 mm dia ‘0’ ring

135” M/F bend consisting of:

135” elbow with ‘0’ ring side F

80 mm dia ‘0’ ring

Vertical eccentric flue exhaust duct

Figures 2.8, 3.8 and 4.8 show the versatility of this

flue system. Measurements and bends must be cal-
culated correctly so as not to oversize maximum flue

lengths.

All spigot ends that are cut must be de-burred with a
file.

All located ‘0’ rings must be lubricated with a sili-
cone grease to ensure easy, snug fit.

NOTE: Exhaust flue must slope 2” down towards the

boiler 35 mm fall per metre.

Spacing Clips

Spacing clips are available on request should they
be required.

Sampling point

Sampling point is positioned on the outlet of the twin

flue header for the use of sampling gas combustion
products.

Condensing trap

To drain the exhaust pipe only with a greater dis-
tance of over 6 metres, a condensating trap must be
fitted, or as an alternative to this the sampling point

may also be used as a condensating drain should

this be required.

Exhaust/suction system with concentric pipes for flat

or sloping roofs. Extensions with two separate pipes.

Maximum distance D = I + E + T = 14 metre + 14 metre
+ 1 metre = 29 metre maximum (pipe + terminal).

Exhaust terminal must not be cut.

NOTE: The pressure loss for each elbow fitted is:

90” elbow less 4 metre of pipe length for each one
fitted.

45” elbow less 1.5 metre of pipe for each one fitted.

For exhaust pipe with a distance of over 6 metre a

condensing trap must be fitted.

Содержание RSF 84E
























































Результаты поиска

Содержание RSF 84E

Отзывы:

Похожие инструкции для RSF 84E

Бренды по названию

Популярные бренды

Ravenheat RSF 84E, Инструкции по установке и обслуживанию

Результаты поиска

Содержание RSF 84E

Отзывы:

Похожие инструкции для RSF 84E

Бренды по названию

Популярные бренды