Ravenheat RSF 84E, Инструкции по установке и обслуживанию

Страница: 11 / 55

SECTION 4
GENERAL REQUlREMENTS
4.0 SAFETY
Gas Safety (Installation and Use)
Regulations, 1994 and amended 2000.
It is law that all gas appliances are installed
and serviced by a CORGI registered
installer in accordance with the above regu-
lations and these installation instructions.
All CORGI registered installers carry a
CORGI I.D. card and have a registration
number. Both should be recorded in your
boiler log book. You can check your installer
by calling CORGI direct on: 01256 732300.
Failure to install appliances correctly could
lead to prosecution. It is in your own inter-
est, and that of safety, to ensure the law is
complied with. Check the boiler and flue is
the correct type for installation.
The installation of the boiler MUST be in
accordance with the latest I.E.E. (BS 7671)
Wiring Regulations, local building regula-
tions, bye-laws of the local water authority,
the building regulations and the Building
Standards (Scotland) and any relevant
requirements of the local authority.
4.1 GENERAL INFORMATION
Both the user and the manufacturer rely heav-
ily on the installer, whose job it is to install the
combination boiler and connect it to a correct-
ly designed heating system. Acquaint yourself
with the British Standards concerning instal-
lation requirements. If you need advice on any
points your Ravenheat Technical Services
Office would be pleased to help. It is recom-
mended that tools suitable for brass fittings
are used, and have a capability to accommo-
date hexagon sizes up to 50 mms.
CODES OF PRACTICE/Ref: Documents
Detailed recommendations are contained in
the following British Standard Codes of
Practice:
BS. 6891
Low pressure installation pipes
BS. 6798
Installation of gas fired hot
water boilers of rated input not
exceeding 60 kW.
BS. 5449
Forced circulation hot water
systems.
BS. 5546 Installation of gas hot water
supplies domestic purposes
(2nd Family Gases).
BS. 544O:1
Flues (for gas appliances of rated
input not exceeding 60 kW).
BS. 5440:2 Ventilation (for gas appliances of
rated input not exceeding 60 kW).
Health & Safety Document No. 635
The Electricity at Work Regulations, 1989.
IMPORTANT. These appliances are CE cer-
tificated for safety and performance. It is,
therefore, important that no external control
devices e.g. flue dampers, economisers
etc., are connected to this appliance unless
covered by these directly Installation and
Servicing Instructions or as otherwise rec-
ommended by Ravenheat in writing. If in
doubt please enquire.
Any direct connection of a control device
not approved by Ravenheat could invalidate
the certification and the normal appliance
warranty. It could also infringe the Gas
Safety regulations and the above regula-
tions.
NOTE: The Ravenheat combination boiler
has been tested an examined by Bg Tech-
nology Certification Services and is certi-
fied to comply with PrEN 483 and BS EN
625.
Manufacturers instructions must NOT be
taken in any way as overriding statutory
obligations.
If in doubt on any point please consult
Ravenheat Manufacturing Ltd.
4.2
LOCATION OF BOILER
4.2.1 Siting of Ravenheat RSF Combi Boiler must
be as follows. The position of installation
should be within the building, unless other-
wise protected by suitable enclosure.
Adequate space for installation, servicing
and air circulation around boiler must be
allowed for.
The Ravenheat RSF Combi Boiler must be
fitted on a flat and vertical wall capable of
adequately supporting the weight of the
boiler and any ancillary equipment.
The appliance may be installed on a com-
bustible wall subject to the requirements of
the Local Authority and Building Regula-
tions.
4.3
CLEARANCES AROUNDTHE
APPLIANCE
4.3.1
The following minimum free spaces, re-
quired for installation inspection and servic-
ing, must be left around the boiler.
RSF 84E (T) RSF 1OOE (T)
Above 125 mm Above 150 mm
Below 100 mm Below 100 mm
Front 450 mm Front 450 mm
Side 75 mm Side 5 mm
25 mm in front when installed in a cupboard
12