Raven SmartYield Pro Скачать руководство пользователя

Страница: 10 / 43

Chapter 2

SmartYield™ Pro Installation Manual

Mount the SmartYield Pro control node on the outside of the vehicle cab. Before mounting the node, review
Chapter 6,

SmartYield™ Pro Control Node Installation

Mount the yield sensors to the clean grain elevator.

Mount the optional moisture sensor to the clean grain elevator or to the grain tank loading auger in the grain
hopper.

Install any required header switch hardware required for the specific harvester make and model.

Kit Contents

TABLE 1.

SmartYield™ Pro Kit Contents

SmartYield Pro

Kit

SmartYield to

SmartYield Pro

Update Kit

Item Description

Part Number

117-9000-002

117-9000-003

Node, SmartYield Pro

063-9000-002

Cable, SmartYield Pro

115-9000-010

Kit, Node Mounting

117-0171-299

Sensors, (Wired Pair)
Optical Yield

063-9000-006

Assembly, Yield Sensor
Optical Lens

063-9000-001

Bracket, Yield Sensor
Mounting

107-0172-134

Bracket, Universal Yield
Sensor Mounting

107-0172-143

Bolt, 1/4”-20 3/4”L Steel Hex
Machine

311-0049-103

Nut, 1/4”-20 Nylon Lock

312-4000-057

Magnet, Yield Sensor
Bracket

418-0000-013

Moisture Sensor Mounting
Kit

117-9000-012

Manual, SmartYield Pro
Installation

016-0171-566

Manual, SmartYield Pro
Calibration and Operation

016-0171-567

Содержание SmartYield Pro











































Результаты поиска

Содержание SmartYield Pro

Отзывы:

Похожие инструкции для SmartYield Pro

Бренды по названию

Популярные бренды

Raven SmartYield Pro, Руководство по установке

Результаты поиска

Содержание SmartYield Pro

Отзывы:

Похожие инструкции для SmartYield Pro

Бренды по названию

Популярные бренды