Raven AutoBoom XRT Скачать руководство пользователя страница 29

Страница: 29 / 72

P/N 016-0235-001 Rev. B

SETTINGS

2. Press Selected Readout in the desired area.
3. Select the desired value for that location from the drop-down at the bottom of the page.
4. After all the Selected Readouts are configured, press Done.

HEIGHT SENSOR CONFIGURATION

The Height Sensor Configuration page allows the user to change the sensor Offset, review software information,

or select Sensor Enable. This page also allows the user to swap the sensors by pressing the Sensor Swap button

and update sensor software by touching the Height Sensor Update button.

Offset X is the horizontal distance from the pivot point of that boom (near the Left or Right Shoulder). Offset Z is

the vertical distance between the spray tip and the lens of the height sensor. If the sensor is below the spray tip,

the Mount should be set to ‘Below.’

FIGURE 4. Height Sensor Configuration

Select the different sensors shown on the sprayer boom to modify that sensors configuration.

Sensor Swap

Height Sensor

Update

Содержание AutoBoom XRT








































































Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды

Raven AutoBoom XRT, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды