Raven AutoBoom XRT Скачать руководство пользователя страница 13

Страница: 13 / 72

P/N 016-0235-001 Rev. B

AUTOBOOM XRT HOME SCREEN AND OPERATION

FIGURE 3. Target Height

TARGET TYPE

Press the Target Type to select between the ground

and canopy

as the desired measurement

target.

MANUAL/AUTO

Depending on the machine configuration, there can be up to three Manual/Auto toggle buttons. Each Manual/

Auto toggle button controls a boom (left/right) or the center rack. If there is not a Manual/Auto button on the

center rack, the center rack is not enabled. When in Auto

mode, the XRT system will continually move the

boom position to reach the target position. When in Manual

mode with the Master Switch on, the system is

ready to engage. Another way to switch from Manual/Auto is to press on the desired boom section.

SENSOR READING

Sensor Height displays the height for each of the sensors. The number of sensors displayed will match the number

of sensors on the machine. The table below describes the Sensor Height reading in more detail.

Содержание AutoBoom XRT








































































Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды

Raven AutoBoom XRT, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды