Raven AutoBoom XRT Скачать руководство пользователя страница 12

Страница: 12 / 72

HAPTER

AutoBoom XRT Calibration & Operation Manual

XRT HOME SCREEN OPERATION

FIGURE 2. XRT Home Screen

MASTER SWITCH

Press the Master Switch

to toggle between enabled and disabled states. If enabled, the system is ready to

transition to auto mode. If disabled, Auto Mode is locked out.

SENSITIVITY SETTINGS

Use the Sensitivity Settings

buttons to increase or decrease the system sensitivity. Increasing the sensitivity

will increase how quickly the boom responds to the sensor target. Increasing the sensitivity too high may result in

unnecessary or excessive movement. Decreasing the sensitivity will result in less boom movement but will make

the booms slower to respond to an error in boom height.

TARGET HEIGHT SETTINGS

Press the Target Height

button to set the distance from the boom to the target. This screen also allows the

user to select the Target Type. This information can also be changed on the XRT Home screen using the +/-

buttons or typing the value into the Target Height box.

Sensor

Reading

Manual

Auto

Sensitivity

Target Height

Sensitivity

Settings

Master

Switch

Target

Type

Target Height

Settings

Содержание AutoBoom XRT








































































Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды

Raven AutoBoom XRT, Калибровка и руководство по эксплуатации

Результаты поиска

Содержание AutoBoom XRT

Отзывы:

Бренды по названию

Популярные бренды