Raven AutoBoom UltraGlide XT Скачать руководство пользователя страница 70

Страница: 70 / 78

HAPTER

Viper Pro Installation & Operation Manual

3. Press the button to manually rotate the boom counterclockwise via the UltraGlide system, verifying that the

boom rotates counterclockwise as viewed from behind the machine.

NOTE:

If the boom rotates in the wrong direction, the UltraGlide XT valve harness corrections may need to

be changed. Refer to Install the Valve Harness section on page 48 for further information.

NOTE:

If there are issues with the AutoBoom system, turn off the machine and correct them immediately. For

additional assistance, refer to the AutoBoom UltraGlide XT Calibration & Operation Manual

(P/N 016-0130-062) or contact your local Raven dealer.

CALIBRATE THE AUTOBOOM ULTRAGLIDE XT SYSTEM

Refer to the AutoBoom UltraGlide XT Calibration & Operation Manual (P/N 016-0130-062) for instructions on

calibrating the system, adjusting system settings, and system operation.

Содержание AutoBoom UltraGlide XT














































































Результаты поиска

Содержание AutoBoom UltraGlide XT

Отзывы:

Raven AutoBoom UltraGlide XT, Руководство по установке, Страница: 70 / 78

Результаты поиска

Содержание AutoBoom UltraGlide XT

Отзывы: