Raven AutoBoom UltraGlide XT Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 78

Raven AutoBoom UltraGlide XT Скачать руководство пользователя страница 55

5

Manual No. 016-0171-122 Rev. E

51

WIRING INSTALLATION

FIGURE 11. AUTOBOOM TIP CONTROL Connectors

3. Locate and disconnect the machine’s AUTOBOOM TIP CONTROL connectors.
4. Plug the AUTOBOOM TIP CONTROL connectors into the mating BOOM SENSE 1 and BOOM SENSE 2

connectors on the node harness cable (P/N 115-0230-104).

FIGURE 12. AutoBoom Node Installed

5. Connect the large, rectangular connectors on the node harness into the correct ports of the AutoBoom node

(P/N 063-0130-023).

6. Tighten the bolts on the node connectors to secure the connections.
7. Secure the AutoBoom node to the node mounting bracket (P/N 107-0171-348) using three 3/8”-16 x 1-1/4” hex

bolts (P/N 311-0054-081) and three 3/8”-16 nylon insert lock nuts (P/N 312-4000-061).

8. Mount the node mounting plate to the node mounting box using the supplied 1/4”-20 x 3/4” self-tapping

screw (P/N 311-0001-345).

9. Install the 31-pin connector on the node harness through the inboard side of the node box, securing it using

the bulkhead washer and lock nut that were removed from the bulkhead plug.

INSTALL THE VALVE HARNESS

NOTE:

The instructions in this section assume that you are standing behind the machine, looking toward the

cab.

AutoBoom Node (P/N

063-0130-023)

Node Connectors

on AutoBoom

Harness

31-Pin Bulkhead

Connector on

AutoBoom Harness

«
...
53
54
55
56
57
...
»

Содержание AutoBoom UltraGlide XT















































































Отзывы:

Нет отзывов