Use and maintenance manual HRB 150 - HRB 200
Rev.1 14/02/18
EN
Pag.52
Introduction
For safe and reliable use:
•
when lighting the first time, unpleasant odors may be created, therefore ensure good ventilation of the room, especially during
the first period of operation;
•
the hopper must only be filled with pellets; make sure the bag does not come into contact with the hot surfaces of the insert;
•
do not put any type of fuel other than recommended wood pellets in the hopper;
•
the unit must not be used as a waste incinerator;
•
the insert must work only and exclusively with the fire door always closed;
•
the fire door seals should be checked periodically to ensure air tightness;
•
to ensure efficient and correct operation, it is necessary to clean the brazier whenever pellets are loaded;
•
when lighting the insert for the first time, make sure to allow it to get hot gradually without overheating;
•
during lighting, operation and shutdown, the insert may creak a little due to the heat expansion.
The insert is operated using a remote control provided with seven buttons and an LCD display. The remote control enables insert
lighting and shutdown, adjustment during operation and the setting of management programs.
The insert also has a button control panel, which can be used instead of the remote control if necessary, allowing only some functions.
Given below is the radio remote control and emergency control panel with the main functions of the buttons:
Use via remote control
The remote control is a device that transmits via radio waves, therefore it does not have to be pointed at the
receiver unit in the control panel.
In an open space, the remote control operating range is over 10 meters. In the presence of walls or other obstacles,
the range can be reduced by a few meters.
Before using the remote control it is necessary to carry out tuning with the electronic board of the insert. This may
be necessary at first activation or when the data communication channel between the board and remote control is
interrupted. In this case, the display will show the message SEARCHING FIELD. The tuning operation may also be
required when there are other appliances which create interference with the insert.
To carry out this operation, proceed as follows:
•
Disconnect the stove power supply.
•
Press buttons P3 and P5 at the same time. The message RADIO ID 0#. will appear. With the scroll buttons select NEW UNIT‘
and confirm with buttons P5.
Select the ID value with the P1 and P2 buttons from 0 to 63 (default ID = 0).
•
Connect the stove power supply.
•
Within 10 seconds after turning on the power, confirm the selected channel by pressing button P5.
2
1
4
5
3
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.18
Pag.19
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Examples of installation of a pellet insert
In this type of installation we can notice that the fitting
was used to enable connecting the insert to the chim
-
ney (so-called “bayonet” mount).
For safety reasons and to ensure proper operation, we
recommend you fit pipes into the chimney. (Fig.7)
It is recommended to perfectly match the insert with
the fitting, to prevent leaks of smoke during the work
phase.
Fig.7
Fig.8
Exploded view of T fit
Protection from rain
Wiring
Connect the power cord to the back of the stove and then to a wall socket. The I/O switch in the figure
should be set to I to power the stove. If voltage is not supplied check the state of the fuse installed in
the box below the switch (4A fuse). During the periods of inactivity, we recommend you disconnect the
power cord of the stove.
Preliminary Operations
NEVER INSERT INTO THE TANK OTHER KIND OF FUEL OTHER FROM THE PELLETS
COMPLYING WITH THE SPECIFICATIONS BELOW
The handheld set is shown in the picture below:
Description of the handheld set:
The information below will allow you to become familiar with the product and achieve the best performance.
How to insert the batteries in the handheld set:
Remove the protective cover of the battery on the back of the remote control as shown in Figure A, and insert the 3 batteries
(mini pen style battery AAA 1.5V) in the housing of the handheld set and observe the poles. Install the battery protective cover
as shown in figure B
The handheld set, after a short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language using the scroll keys and confirm your selection with the confirmation button.
1
Increase button “UP” (selection key)
2
Decrease key “DOWN” (selection key)
3
ON/OFF or reset from “Sleep” mode key.
4
Display
5
Key for accessing the MENU and back
6
Confirmation key
1
2
5
6
4
3
Figure A
Figure B
Here you can see the possibility to slide
the insert; this operation can only be performed
with the stove turned off for loading pellets or during
regular checks. (Fig.8)
IT IS STRICTLY FORBIDDEN
TO REMOVE THE STOVE DURING
THE WORK PHASES; THE FUME
MAY DISPERSE INTO THE
In “Sleep” mode, the handheld set
screen is obscured, keeping however
active the radio communication with
the stove to reduce battery con-
sumption.
T fitting with
inspection ash
collector cap
Flue
Protection from rain
Pipe
Flue
Pipe
What to check befor turning on the stove
Make sure you have removed all parts that pose the risk of burns from the combustion chamber or glass (various instructions or
stickers).
Before turning on the stove, make sure you have fitted the grate on the support base and check that the door and the ash drawer
are properly close.
How to load the pellets
Fuel supply consists in the insertion of pellets from the top of the stove, by opening the door. During pellet loading prevent the pel
-
let bag from coming into contact with hot surfaces.
Data transfer
active
Alarm active
P3: On and off
button
P1-P2: Power
selection buttons
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.18
Pag.19
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Examples of installation of a pellet insert
In this type of installation we can notice that the fitting
was used to enable connecting the insert to the chim
-
ney (so-called “bayonet” mount).
For safety reasons and to ensure proper operation, we
recommend you fit pipes into the chimney. (Fig.7)
It is recommended to perfectly match the insert with
the fitting, to prevent leaks of smoke during the work
phase.
Fig.7
Fig.8
Exploded view of T fit
Protection from rain
Wiring
Connect the power cord to the back of the stove and then to a wall socket. The I/O switch in the figure
should be set to I to power the stove. If voltage is not supplied check the state of the fuse installed in
the box below the switch (4A fuse). During the periods of inactivity, we recommend you disconnect the
power cord of the stove.
Preliminary Operations
NEVER INSERT INTO THE TANK OTHER KIND OF FUEL OTHER FROM THE PELLETS
COMPLYING WITH THE SPECIFICATIONS BELOW
The handheld set is shown in the picture below:
Description of the handheld set:
The information below will allow you to become familiar with the product and achieve the best performance.
How to insert the batteries in the handheld set:
Remove the protective cover of the battery on the back of the remote control as shown in Figure A, and insert the 3 batteries
(mini pen style battery AAA 1.5V) in the housing of the handheld set and observe the poles. Install the battery protective cover
as shown in figure B
The handheld set, after a short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language using the scroll keys and confirm your selection with the confirmation button.
1
Increase button “UP” (selection key)
2
Decrease key “DOWN” (selection key)
3
ON/OFF or reset from “Sleep” mode key.
4
Display
5
Key for accessing the MENU and back
6
Confirmation key
1
2
5
6
4
3
Figure A
Figure B
Here you can see the possibility to slide
the insert; this operation can only be performed
with the stove turned off for loading pellets or during
regular checks. (Fig.8)
IT IS STRICTLY FORBIDDEN
TO REMOVE THE STOVE DURING
THE WORK PHASES; THE FUME
MAY DISPERSE INTO THE
In “Sleep” mode, the handheld set
screen is obscured, keeping however
active the radio communication with
the stove to reduce battery con-
sumption.
T fitting with
inspection ash
collector cap
Flue
Protection from rain
Pipe
Flue
Pipe
What to check befor turning on the stove
Make sure you have removed all parts that pose the risk of burns from the combustion chamber or glass (various instructions or
stickers).
Before turning on the stove, make sure you have fitted the grate on the support base and check that the door and the ash drawer
are properly close.
How to load the pellets
Fuel supply consists in the insertion of pellets from the top of the stove, by opening the door. During pellet loading prevent the pel
-
let bag from coming into contact with hot surfaces.
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.18
Pag.19
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Examples of installation of a pellet insert
In this type of installation we can notice that the fitting
was used to enable connecting the insert to the chim
-
ney (so-called “bayonet” mount).
For safety reasons and to ensure proper operation, we
recommend you fit pipes into the chimney. (Fig.7)
It is recommended to perfectly match the insert with
the fitting, to prevent leaks of smoke during the work
phase.
Fig.7
Fig.8
Exploded view of T fit
Protection from rain
Wiring
Connect the power cord to the back of the stove and then to a wall socket. The I/O switch in the figure
should be set to I to power the stove. If voltage is not supplied check the state of the fuse installed in
the box below the switch (4A fuse). During the periods of inactivity, we recommend you disconnect the
power cord of the stove.
Preliminary Operations
NEVER INSERT INTO THE TANK OTHER KIND OF FUEL OTHER FROM THE PELLETS
COMPLYING WITH THE SPECIFICATIONS BELOW
The handheld set is shown in the picture below:
Description of the handheld set:
The information below will allow you to become familiar with the product and achieve the best performance.
How to insert the batteries in the handheld set:
Remove the protective cover of the battery on the back of the remote control as shown in Figure A, and insert the 3 batteries
(mini pen style battery AAA 1.5V) in the housing of the handheld set and observe the poles. Install the battery protective cover
as shown in figure B
The handheld set, after a short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language using the scroll keys and confirm your selection with the confirmation button.
1
Increase button “UP” (selection key)
2
Decrease key “DOWN” (selection key)
3
ON/OFF or reset from “Sleep” mode key.
4
Display
5
Key for accessing the MENU and back
6
Confirmation key
1
2
5
6
4
3
Figure A
Figure B
Here you can see the possibility to slide
the insert; this operation can only be performed
with the stove turned off for loading pellets or during
regular checks. (Fig.8)
IT IS STRICTLY FORBIDDEN
TO REMOVE THE STOVE DURING
THE WORK PHASES; THE FUME
MAY DISPERSE INTO THE
In “Sleep” mode, the handheld set
screen is obscured, keeping however
active the radio communication with
the stove to reduce battery con-
sumption.
T fitting with
inspection ash
collector cap
Flue
Protection from rain
Pipe
Flue
Pipe
What to check befor turning on the stove
Make sure you have removed all parts that pose the risk of burns from the combustion chamber or glass (various instructions or
stickers).
Before turning on the stove, make sure you have fitted the grate on the support base and check that the door and the ash drawer
are properly close.
How to load the pellets
Fuel supply consists in the insertion of pellets from the top of the stove, by opening the door. During pellet loading prevent the pel
-
let bag from coming into contact with hot surfaces.
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.18
Pag.19
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Examples of installation of a pellet insert
In this type of installation we can notice that the fitting
was used to enable connecting the insert to the chim
-
ney (so-called “bayonet” mount).
For safety reasons and to ensure proper operation, we
recommend you fit pipes into the chimney. (Fig.7)
It is recommended to perfectly match the insert with
the fitting, to prevent leaks of smoke during the work
phase.
Fig.7
Fig.8
Exploded view of T fit
Protection from rain
Wiring
Connect the power cord to the back of the stove and then to a wall socket. The I/O switch in the figure
should be set to I to power the stove. If voltage is not supplied check the state of the fuse installed in
the box below the switch (4A fuse). During the periods of inactivity, we recommend you disconnect the
power cord of the stove.
Preliminary Operations
NEVER INSERT INTO THE TANK OTHER KIND OF FUEL OTHER FROM THE PELLETS
COMPLYING WITH THE SPECIFICATIONS BELOW
The handheld set is shown in the picture below:
Description of the handheld set:
The information below will allow you to become familiar with the product and achieve the best performance.
How to insert the batteries in the handheld set:
Remove the protective cover of the battery on the back of the remote control as shown in Figure A, and insert the 3 batteries
(mini pen style battery AAA 1.5V) in the housing of the handheld set and observe the poles. Install the battery protective cover
as shown in figure B
The handheld set, after a short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language using the scroll keys and confirm your selection with the confirmation button.
1
Increase button “UP” (selection key)
2
Decrease key “DOWN” (selection key)
3
ON/OFF or reset from “Sleep” mode key.
4
Display
5
Key for accessing the MENU and back
6
Confirmation key
1
2
5
6
4
3
Figure A
Figure B
Here you can see the possibility to slide
the insert; this operation can only be performed
with the stove turned off for loading pellets or during
regular checks. (Fig.8)
IT IS STRICTLY FORBIDDEN
TO REMOVE THE STOVE DURING
THE WORK PHASES; THE FUME
MAY DISPERSE INTO THE
In “Sleep” mode, the handheld set
screen is obscured, keeping however
active the radio communication with
the stove to reduce battery con-
sumption.
T fitting with
inspection ash
collector cap
Flue
Protection from rain
Pipe
Flue
Pipe
What to check befor turning on the stove
Make sure you have removed all parts that pose the risk of burns from the combustion chamber or glass (various instructions or
stickers).
Before turning on the stove, make sure you have fitted the grate on the support base and check that the door and the ash drawer
are properly close.
How to load the pellets
Fuel supply consists in the insertion of pellets from the top of the stove, by opening the door. During pellet loading prevent the pel
-
let bag from coming into contact with hot surfaces.
User’s manual HANDHELD TOUCH RADIO
User’s manual HANDHELD TOUCH RADIO
Pag.18
Pag.19
Vers. 01 of:07.04.14
Vers. 01 of:07.04.14
Examples of installation of a pellet insert
In this type of installation we can notice that the fitting
was used to enable connecting the insert to the chim
-
ney (so-called “bayonet” mount).
For safety reasons and to ensure proper operation, we
recommend you fit pipes into the chimney. (Fig.7)
It is recommended to perfectly match the insert with
the fitting, to prevent leaks of smoke during the work
phase.
Fig.7
Fig.8
Exploded view of T fit
Protection from rain
Wiring
Connect the power cord to the back of the stove and then to a wall socket. The I/O switch in the figure
should be set to I to power the stove. If voltage is not supplied check the state of the fuse installed in
the box below the switch (4A fuse). During the periods of inactivity, we recommend you disconnect the
power cord of the stove.
Preliminary Operations
NEVER INSERT INTO THE TANK OTHER KIND OF FUEL OTHER FROM THE PELLETS
COMPLYING WITH THE SPECIFICATIONS BELOW
The handheld set is shown in the picture below:
Description of the handheld set:
The information below will allow you to become familiar with the product and achieve the best performance.
How to insert the batteries in the handheld set:
Remove the protective cover of the battery on the back of the remote control as shown in Figure A, and insert the 3 batteries
(mini pen style battery AAA 1.5V) in the housing of the handheld set and observe the poles. Install the battery protective cover
as shown in figure B
The handheld set, after a short screen showing the Ravelli logo, will list the languages available in the menu.
Select the desired language using the scroll keys and confirm your selection with the confirmation button.
1
Increase button “UP” (selection key)
2
Decrease key “DOWN” (selection key)
3
ON/OFF or reset from “Sleep” mode key.
4
Display
5
Key for accessing the MENU and back
6
Confirmation key
1
2
5
6
4
3
Figure A
Figure B
Here you can see the possibility to slide
the insert; this operation can only be performed
with the stove turned off for loading pellets or during
regular checks. (Fig.8)
IT IS STRICTLY FORBIDDEN
TO REMOVE THE STOVE DURING
THE WORK PHASES; THE FUME
MAY DISPERSE INTO THE
In “Sleep” mode, the handheld set
screen is obscured, keeping however
active the radio communication with
the stove to reduce battery con-
sumption.
T fitting with
inspection ash
collector cap
Flue
Protection from rain
Pipe
Flue
Pipe
What to check befor turning on the stove
Make sure you have removed all parts that pose the risk of burns from the combustion chamber or glass (various instructions or
stickers).
Before turning on the stove, make sure you have fitted the grate on the support base and check that the door and the ash drawer
are properly close.
How to load the pellets
Fuel supply consists in the insertion of pellets from the top of the stove, by opening the door. During pellet loading prevent the pel
-
let bag from coming into contact with hot surfaces.
