Rational iCombi Pro страница 21 Скачать руководство пользователя

Страница: 21 / 96

4 | Transport

80.06.083_iCombiPro-iCombiClassic_IM_en-US

21 / 96

NOTE

Transport with transport aid without protection

Transport the device on the pallet for as long as possible. Do not transport
the device with a transport aid or similar transport equipment without
protection. Use a wooden board for protection, for example.

Required door width with transport pallet

Unit size

6 half
size

6 full
size

10 half
size

10 full
size

20 half
size

20 full
size

x (mm)

880

945

1150

945

1150

989

1194

x (inch)

34 5/8

37 1/4

45 1/4

37 1/4

45 1/4

38 7/8

y (mm)

930

935

1170

935

1170

969

1174

Y (inch)

36 5/8

36 3/4

46 1/8

36 3/4

46 1/8

38 1/8

46 1/4

Transport tabletop devices with transport pallet

The packaging material is removed.

The device is on the transport pallet.

The device rests on the device base frame.

1. Transport the device to the installation site with the transport pallet.

2. Lift the device off the transport pallet on the lifting points and set it down

on the designated installation surface.

The device is on the designated installation surface and is ready for setup
and installation.

Transport floor devices with transport pallet

Floor devices are delivered on a special, divisible transport pallet.

Содержание iCombi Pro

































































































Результаты поиска

Содержание iCombi Pro

Отзывы:

Похожие инструкции для iCombi Pro

Бренды по названию

Популярные бренды

Rational iCombi Pro, Оригинальная инструкция по установке

Результаты поиска

Содержание iCombi Pro

Отзывы:

Похожие инструкции для iCombi Pro

Бренды по названию

Популярные бренды