background image

14 | Decommissioning

88 / 96

80.06.083_iCombiPro-iCombiClassic_IM_en-US

14

Decommissioning

14.1 Notes on decommissioning

Observe the following when decommissioning the device:

n

Make sure that the device has cooled down to below 40°C [104°F].

n

Make sure that the steam generator is pumped empty.

n

Make sure that the cleaning box is pumped empty.

n

Switch off the gas supply.

n

Make sure that the device is de-energized and disconnected from the
power supply.

n

Remove all water, wastewater and, for gas devices, additional gas connec-
tions from the device.

n

If the device is to be transported, remove the device from the foot locking
mechanisms and from any wall mountings (mounting chain).

14.2 Disposal

Electrical and electronic devices such as iCombi Pro and iCombi Classic must
be disposed of separately.

n

Do not dispose of the device as household waste or in the old equipment
container at municipal connection points.

n

Observe the country-specific regulations for device disposal.

n

Where necessary, contact the manufacturer for further information on dis-
posal.

Содержание iCombi Pro

































































































Отзывы: