background image

Page 7

Powering Emergency Phone Options

Step 9

Options for powering the Emergency Phones.

Option 1

Rath 2500-PWR24 Power Supply:

 

•  Use 1-pair 18 AWG wire for power, maximum distance of 5,100’

 

•  Do NOT wire more than 3 devices per wire run and a maximum of 11 devices per Power Supply

Powering Emergency Phone Options

 Page 3

SOLID LIGHT: 

CALLING

BLINKING LIGHT: 

RECEIVED

0

2
5

3

1

4

6

7 8 9

*

#

SOLID LIGHT: 

CALLING

BLINKING LIGHT: 

RECEIVED

0

2

5

3

1

4

6

7 8 9

*

#

SOLID LIGHT: 

CALLING

BLINKING LIGHT: 

RECEIVED

0

2

5

3

1

4

6

7 8 9

*

#

0

2
5

3

1

4

6

7 8 9

*

#

SOLID LIGHT: 

CALLING

BLINKING LIGHT: 

RECEIVED

0

2
5

3

1

4

6

7 8 9

*

#

2 Pair- Twisted

24-22ga

2 Pair- Twisted

24-22ga

2 Pair- Twisted

24-22ga

2 Pair- Twisted

24-22ga

2 Pair- Twisted

24-22ga

2500-PWR24

1 Pair

18ga

Hot

To 120vac

Ground

Neutral

SOLID LIGHT: 

CALLING

BLINKING LIGHT: 

RECEIVED

EMERGENCY PHONE

EMERGENCY PHONE

EMERGENCY PHONE

EMERGENCY PHONE

EMERGENCY PHONE

Rescue Services

Submaster 1

Submaster 2

Battery:

Green: Full Charge

Yellow: Mid-level Charge

Red: Low Charge

Read all operating steps before proceeding.

Operation:

1.  Solid lit 

LED

 (Phone, Sub-Master or Rescue Services)

     indicates 

Call in Progress.

2.  Slow blinking 

LED

 indicates 

Call on Hold.

3.  Lift Handset.
4.  Press yellow 

TALK/HOLD

 button to call in to a specific 

     Sub-Master. If the green 

LED

 is lit you will join conversation.

5.  Press black 

TALK/HOLD

 button to call in to a specific Phone. 

     If the green 

LED

 is lit you will join conversation.

6.  Press 

TALK/HOLD

 button again to place conversation on hold.

7.  Press red 

Disconnect Call to Rescue Services

 button to 

     end external call. Any Phone and Sub-Master originally talking

     remain in conversation with this unit.
8.  Hang up Handset to end calls to Phone and Sub-Master.

Battery

AC Power

Phone 1

Phone 2

Phone 3

Phone 4

Phone 5

 

Disconnect Call 

to Rescue Services

800-451-1460

www.rathmicrotech.com

www.area-of-refuge.com

SmartRescue Phone - 5

Do NOT power

SmartRescue 

with this

Option 2

Transformers: 

Only applicable if your phone comes with one supplied by Rath

Option 3

Powered Directly by Elevator Car

Содержание SmartRescue 5















Отзывы: