manualshive.com logo in svg
background image

Installation:

1. Using the supplied spanner bit, remove the 4 screws holding the front cover in place and then remove the cover.

2. Using a drill bit or knockout set, drill a hole in the bottom of the enclosure large enough for the water tight connector.

3. Using appropriate mounting screws, screw enclosure onto the wall.

4. Run telephone line in conduit, bring line into the enclosure through the water tight connector, and tighten conduit 

    to connector.

5. Connect the incoming line to the RJ11 connector and plug into the RJ11 jack on board. Or, obtain a biscuit jack, 

    terminate your incoming line to the biscuit jack, and plug the included phone line into the RJ11 connector on the 

    biscuit jack. 

    

Note:

 Do not cut RJ11 jack of supplied line cord and splice phone line onto it. 

6. Run 120vac in the other conduit and water tight connector. Connect 120vac to the supplied transformer in the 

   enclosure using proper wire nuts. Red is hot, black is neutral, and green is ground (see page 8 for a more 

   detailed wiring diagram).

   

Note:

 The transformer is wrapped separately in the box. 

7. Locate the green battery backup pack in the enclosure. Plug the white connector located on the battery pack into 

    the “BATTERY” connector in the bottom left corner of the yellow board.

8. Turn on electrical power.

9. Phone is preset to dial 911. If required to call an alternate number not given to RATH® at time of purchase, please 

    follow programming instructions on page 7. If phone is calling 911, screw internal plate back into place. Unit is 

    ready for testing. 

Items Needed:

• Live digital phone line

• Drill

• Metal capable drill bit or knockout set

• Biscuit jack (provided)

• Mounting screws

• Wall anchors

• Conduit with water tight connector

• 3/32 Allen wrench (provided)

• Screwdriver

690RDPOOLD, 690SYPOOLD (YELLOW)

Page 4

Items Needed:

• Live digital phone line

• 120vac power

• Drill

• Drill bit or knockout set

• Biscuit jack

• Mounting screws

• #10 spanner bit (provided)

• Conduit with (2) water tight connectors

• Wire nuts

• Screwdriver

984LPOOL, 984LPOOLC1

Содержание 624POOLD








Отзывы: