Ranger R30XLT, Инструкция по установке и эксплуатации

Страница: 28 / 48

28
STAgE fOuR / TIRE INfLATION
1. Make sure both beads are seated. When both beads are
seated, the tire is ready for inflation.
2. Replace the valve core if it was removed.
3. Depress the Inflation Pedal to inflate the tire. DO NOT
STAND OVER TIRE DURING INFLATION.
4. Do not inflate the tire above the manufacturer’s recom-
mended pressure as stamped on the tire sidewall. The
typical inflation pressure for automobile tires is between 24
and 45 PSI. Light truck inflation pressure typically covers a
wider range. Release air pressure from the tire by pressing
the manual Pressure Relief Valve.
wARNINg!
NEVER ATTEMPT TO MOUNT AND INFLATE MIS-
MATCHED TIRES AND WHEELS. MISMATCHED TIRE
AND WHEEL COMBINATIONS CAN EXPLODE, CAUS-
ING PERSONAL INjURY OR DEATH TO OPERATOR
AND BYSTANDERS. FOR SAFETY, DO NOT ATTEMPT
TO MOUNT AND INFLATE MISMATCHED TIRES AND
WHEELS.
wARNINg!
IF OPERATOR IS UNABLE TO OBTAIN BEAD SEAT,
SOMETHING IS WRONG. DEFLATE TIRE COM-
PLETELY, INSPECT TIRE AND WHEEL, CORRECT
ANY PROBLEMS FOUND, RE-LUBRICATE BOTH TIRE
BEADS, AND REATTEMPT BEAD SEAL AND SEAT
PROCEDURES. FOLLOW ALL SAFETY INSTRUC-
TIONS IN THIS MANUAL AND ON MACHINE.
wARNINg!
CHECK TIRE PRESSURE FREqUENTLY. NEVER
EXCEED 40 PSI WHILE SEATING BEADS. ONCE
SEATED, NEVER EXCEED TIRE MANUFACTURER’S
RECOMMENDED AIR PRESSURE. TIRES CAN
EXPLODE, ESPECIALLY IF THEY ARE INFLATED
BEYOND THEIR LIMITS. AT ALL PRESSURE LEVELS
WHEN INFLATING THROUGH THE VALVE STEM,
KEEP HANDS, ARMS, AND ENTIRE BODY AWAY
FROM INFLATING TIRE. AN EXPLODING TIRE,
WHEEL, OR BEAD SEALING EqUIPMENT MAY PRO-
PEL UPWARD AND OUTWARD WITH SUFFICIENT
FORCE TO CAUSE SERIOUS INjURY OR DEATH TO
OPERATOR OR BYSTANDER.
wARNINg!
THE INFLATION PRESSURE LIMITER IS
PRESET AT THE FACTORY AND SHOULD NEED
NO ADjUSTMENT. ADjUST ONLY IF PRESSURE
EXCEEDS 60 PSI. OPERATING A TIRE CHANGER
WITH A DEFECTIVE, IMPROPERLY ADjUSTED, OR
BYPASSED PRESSURE LIMITER COULD RESULT IN A
TIRE EXPLOSION WITH SEVERE INjURY OR DEATH
TO OPERATOR OR BYSTANDERS. ALWAYS BE SURE
THAT THE PRESSURE LIMITER IS OPERATING PROP-
ERLY ON THE MACHINE AT ALL TIMES. PRESSURE
LIMITER IS SET AT 60 PSI. ANY REqUIRED INFLA-
TION ABOVE 60 PSI SHOULD BE PERFORMED IN AN
INFLATION CHAMBER/SAFETY CAGE.
NOTE:
WHEN INFLATING TIRES THAT REqUIRE MORE
THAN 60 PSI, ALWAYS USE A SAFETY CAGE AND
AIR HOSE WITH A CLIP-ON AIR CHUCK AND IN-LINE
VALVE. THE HOSE MUST HAVE ENOUGH LENGTH
BETWEEN THE CHUCK AND THE OPERATION/IN-
LINE VALVE TO ALLOW THE OPERATOR TO STAND
OUTSIDE THE TRAjECTORY.
t
BEFORE MAKING ANY INSPECTION, ADjUSTMENT,
OR REPAIR, DISCONNECT THE POWER SOURCE
AND OR AIR SUPPLY AND BLOCK OUT ALL MOVING
PARTS TO PREVENT INjURY.
t KEEP THE MACHINE AND THE IMMEDIATE WORK
AREA CLEAN. DO NOT USE COMPRESSED AIR TO
REMOVE DIRT AND DEBRIS FROM THE MACHINE.
FOREIGN MATERIAL MAY BE PROPELLED INTO THE
AIR AND INTO OPERATOR OR BYSTANDER CAUSING
PERSONAL INjURY.
t
WEAR PROTECTIVE CLOTHING AND USE EYE
PROTECTION WHEN MAKING ANY ADjUSTMENTS OR
REPAIRS TO THE MACHINE.