manualshive.com logo in svg

RAK RAK19001, Быстрый старт

Поделиться
Скачать
RAK RAK19001 Скачать руководство пользователя страница 15

Documentation Center

LEDs

Three LEDs are used to indicate the operating status. Below are the functions of the LEDs:

🔴

 Red LED - Connected to the charger chip to indicate the charger status. When the battery is charging, this

red LED is on. When the battery is full, this LED is weak light or off.

 Green LED - Connected to the MCU module, controlled by MCU defined by the user.

🔵

 Blue LED - Connected to the MCU module, controlled by MCU defined by the user.

RESET Push Button

The Reset Push Button shown in 

Figure 3 of interfaces section

 is connected to the MCU module. When pushed, it

resets the MCU.

User Programmable Push Button

The User Programmed Push Button shown in 

Figure 3 of interfaces section

 is connected to the SW1 pin of the

WisBlock Core.

Pin Definition

Connector for WisBlock Core

The WisCore module connector is a 40-pin board-to-board connector. It is a high-speed and high-density
connector, with an easy attaching mechanism.

Figure 11: WisBlock Core module 40-pin connector

The table below shows the pinout of the 40-pin MCU module connector:

Содержание RAK19001
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды