background image

Rain Master Irrigation Systems 

Weather Station Manual

 

Page 19 

through the evaporating plate surface, more water is drawn through the electronic pulse 
monitor, located on the electronics board, where it is measured at the rate of one pulse 
for every 0.01” of ET.  A miniature motor, also  located on the electronics board 
assembly, supplies the water pressure necessary to keep the ceramic cup filled. The 
motor is also used to purge the water lines of air bubbles when priming the system.  

 

3.1.3 ET Tracker Specifications 

The ET Tracker is capable of measuring the evapotranspiration for any given 
microclimate. It  produces a single pulse for every 0.01” of ET and is capable of 
communicating the occurance of the pulse to the Rain Master Evolution DX2 controller 
equipped with the necessary sensor board (DX-FLOW or DX-MOIST). 

 

Sensor Accuracy:   

+/-1% of evapotranspiration. 

Sensor Resolution: 

 

0.01” reference Evapotranspiration ( ET). 

Sensor Output: 

A single pulse per 0.01” ET. 

Capacity:  

 

Reservoir contains 12 inches of distilled water per ET 
filling. 

Installation:   

Connects directly into a Rain Master Evolution DX2 
controller equipped with a sensor board.  The ET is read 
directly from the Evolution DX2 controller by the Evolution 
Central Computer. 

Dimensions:   

34.5 inches high  x 3.1 inches in diameter 

Weight:  

 

3.5 pounds empty, 7.85 pounds filled with water 

Mounting:    

Inside Weather Station tower 

Materials:    

Ceramic evaporating plate, green canvas cover, PVC 
Plastic housing 

Electrical  

Signal: 

Electrical signal is pulsed low for  2.3 (+/- .07) seconds 
after each 0.01” ET pulse. 

Impedance:   

Normally open circuit of 53 OHMS during pulse. (Max 
voltage from receiving equipment: 30V DC) 

Transient Protection: 

Full lightning protected, except direct  strikes to the unit. 

Power Source Internal 
Backup Supply: 

Four (4) alkaline “AA” cells (6 Volts DC). 

External Supply 
Connection: 

5 to 16V DC, 0.1 A peak 0.4 MA average. Internal screw 
terminal block. 

Freeze Protection: 

Unit must be drained during freezing season. 

 

Содержание ET Tracker













































Отзывы: