1 0
1 1
www.raider.bg
Original instructions for use
Dear Customer,
Congratulations on the purchase of machinery from the fastest growing brand of electric,
gasoline and pneumatic machines - RAIDER. When properly installed and operating, RAIDER are
safe and reliable machines and work with them will deliver a real pleasure. For your convenience
has been built and excellent service network of 45 service station across the country.
Before using this machine, please carefully acquainted with these “instructions for use.
In the interest of your safety and to ensure proper use and read these instructions carefully,
including the recommendations and warnings in them. To avoid unnecessary errors and accidents,
it is important that these instructions will remain available for future reference to all who will use
the machine. If you sell it to a new owner “Instructions for Use” must be submitted along with it to
enable new users to become familiar with relevant safety and operating instructions.
Euromaster Import Export Ltd. is an authorized representative of the manufacturer and owner
of the trademark RAIDER.
Adress: Sofia City 1231, Bulgaria “Lomsko shausse” Blvd. 246, tel +359 700 44 155, www.raider.
bg; www.euromasterbg.com; e-mail: [email protected] 2006 the company introduced
the system of quality management ISO 9001:2008 with scope of certification: Trade, import, export
and servicing of hobby and professional electrical, mechanical and pneumatic tools and general
hardware. The certificate was issued by Moody International Certification Ltd, England.
TECHNICAL DATA
parameter
unit
value
Model
-
R D - C S 2 8
Rated power
W
1 4 8 0
Current
V
2 3 0
Frequency
H z
5 0
Sound pressure
dB(А)
9 6
Sound power
dB(А)
1 0 5
Vibrations
m / s
2
2.75
Max speed
m in -
1
13 800
Inside diameter of the disc
m m
2 0
Max diameter of the disc
m m
1 1 0
Maximum cut at 90 °
m m
3 5
Protection class
-
II
Level of protection
-
IP21
EN
GENERAL POWER TOOL SAFETY WARNINGS.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury. Save all warnings and Instructions for future reference.
CIRCULAR SAW SAFETY WARNINGS.
Usage. This machine is suitable for cutting wood, other similar materials and plastic.
BLADE CHANGING PROCEDURE:
Pull the plug out of the socket before making adjustments or servicing. Press the lockout button on the
rotor and hold it down. Slowly rotate the disc with the key until the lock is triggered. Unscrew the disc fixing
screw by turning left. Pull the fuse with the lever and remove the disc. The contact areas between the inner
flange, disc, outer flange and fixing screw must be dust-free. Insert a new disc, making sure the direction
of rotation is correct. The direction of rotation is indicated by the arrow on the disc and on the fuse. Tighten
the fixing screw.
Do not use abrasive discs. Use only sharp, undamaged discs. Do not use cracked or discolored discs. Do
not use discs made of highly alloyed high-speed steel. Do not use discs that do not meet these guidelines.
The disc must be suitable for idle speed. Use a cutting disc suitable for the workpiece.
BEFORE USE
Attention! Before you start working with circular saw, check the voltage and frequency of the
electrical network.
Attention! Check whether the protective cover is moving normally, without interfering in some sort
of way blade.
Attention! Place the blade by selecting disk rendered technical parameters.
1. Check the blade meets the following requirements: its speed is equal to or greater than that of the
circular.
Attention! Never use cracked or damaged saw blade.
2. Before placing the blade make sure saw is disconnected from the power cord. And the key is in position
“OFF”.
FIXING DETAIL
Place the workpiece as proved in the figure below
To prevent “kick” of the circular do not put the detail in the following way:
