Rae QRAE PLUS PGM-2000 Скачать руководство пользователя страница 28

Страница: 28 / 88

OPERATION

2-15

Table 4.

Alarm Signals and Reset

Condition

Alarm Signal

Message on

the LCD

Alarm Reset by

Gas exceeds
“High Alarm” limit

3 beeps/flashes

per second /

Vibration

Sensor name

and “High”

Move away from the
gas.

Gas exceeds
“Low Alarm” limit

2 beeps/flashes

per second /

Vibration

Sensor name

and “Low”

Move away from the
gas.

Gas exceeds
STEL

1 beep/flash per

second /

Vibration

Sensor name

and “STEL”

Move away from the
gas and wait 15
minutes.

Gas exceeds
TWA

1 beep/flash per

second /

Vibration

Sensor name

and “TWA”

Move away from the
gas, turn the unit OFF
and then back ON.

Gas exceeds the
sensor range

3 beeps/flashes

per second /

Vibration

Sensor name

and “OVR”

Move away from the
gas.

Water sucked in,
unit short circuit
or reading out of
the maximum
range

3 beeps/flashes

per second /

Vibration

Sensor name

and “MAX”

Move away from the
gas.

Excessive sensor
negative drifting

1 beep/flash per

second /

Vibration

Sensor name

and “NEG”

Perform a fresh-air
zero calibration.

Blocked inlet or
pump failure

3 beeps/flashes

per second

“Pump”

Unblock the inlet and
press the

[Y/+]

key,

adjust pump
threshold.

Excessive LEL
gas or LEL sensor
OFF

3 beeps/flashes

per second /

Vibration

LEL sensor

name and “Off”

Move away from the
gas and turn the LEL
sensor back ON.

Low battery

1 flash per

second, 1 beep

per minute

“Bat”

Charge the battery.

Memory full

1 flash per

second

“Mem”

Clear the datalog.

Datalog memory
write error

1 flash per

second

“Emm”

Turn the unit OFF and
then back ON.

Содержание QRAE PLUS PGM-2000

























































































Результаты поиска

Содержание QRAE PLUS PGM-2000

Отзывы:

Похожие инструкции для QRAE PLUS PGM-2000

Бренды по названию

Популярные бренды

Rae QRAE PLUS PGM-2000, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание QRAE PLUS PGM-2000

Отзывы:

Похожие инструкции для QRAE PLUS PGM-2000

Бренды по названию

Популярные бренды