background image

13

7) Additional Information

7) Additional Information

7-1. Mounting the Base on a Wall

7-1. Mounting the Base on a Wall

You can mount the phone on any standard telephone jack wall plate.

1.

 

Route the AC adapter and the modular 
cords through the hole of the wall mount 
bracket (supplied).

2.

  Connect the AC adapter and the modular 

cords as shown. Remember to route the 
AC adapter cord through the channel.

3.

  Line up the four tabs on the wall mount 

bracket (two at the top and two at the bottom) with the 
four notches on the bottom of the base. Slide the bracket 
into place.

4.

  Hook the AC adapter cord into the smaller notch at the bottom of the bracket, and let 

the cord hang below the bracket.

5.

  Plug the modular cord into the wall jack. Hook both sides of the modular cord into the 

larger notch OR tuck the excess cord into the open space in the bracket.

Wall plate

To AC outlet

AC adapter (supplied)

To telephone
wall jack

Modular cord (supplied)

6.

  Place the mounting slots over the pins on the wall plate.

7.

  Slide the base to lock it into place.

Wall plate

Note:

 To mount the phone directly on the wall, insert two 

1-3/8 inch, #10 screws (not supplied) into the wall using 
anchors suitable for the wall material. Place the screws 
3-15/16 inches apart, and allow 1/8 inch free space between 
the wall and screw heads.

Removing the Base from the Wall Mount Bracket

Removing the Base from the Wall Mount Bracket 

While pulling the release latch on the bracket 
with one hand, slide the base away from the 
bracket.

7-2. Using the Belt Clip

7-2. Using the Belt Clip

To attach the belt clip

To attach the belt clip

Insert the tabs on the side of the belt clip (supplied) into the 
holes on either side of the handset. Press the belt clip down until 
it clicks into place. (Tug on the clip to make sure it’s secure.)

To remove the belt clip

To remove the belt clip

Gently pull the tabs out of the holes, then slide the belt clip off of 
the handset.

7-3. Troubleshooting and Maintenance

7-3. Troubleshooting and Maintenance

Solving Common Issues

Solving Common Issues

If your phone is not performing to your expectations, please try these simple steps fi rst. 
If these steps do not solve your problem, take it  to your local 

RadioShack

 store for 

assistance.

Release latch

Release latch

Содержание Presidian

















Отзывы: