background image

GENERAL INFORMATION

 

 

 

1

1. GENERAL INFORMATION 

 

1.1 General warnings 

  Professionally  qualified  personnel  in  accordance  with  current  laws  and  standards  and  in  line  with  the 

manufacturer’s instructions must install the appliance.  

 

In  GB,  the  installation  must  be  carried  out  by  a  Gas Safe  Registered  Installer.  To  check  for  authorised 
qualified  engineers  please  contact 

Phone  Number  0800  408  5500.

  It  must  be  carried  out  in  accordance 

with the relevant requirements of the: 

Gas Safety Regulations; 

The  appropriate  Building  Regulations  either  The  Building  Regulation,  The  Building  Regulations 
(Scotland), Building Regulations (Northern Ireland); 

The Water Fittings Regulations or Water Byelaws in Scotland; 

The current I.E.E. Wiring Regulations. 

Where  no  specific  instructions  are  given,  reference  should  be  made  to  the  relevant  British  Standards 
Code of Practice. 

 

  The  commissioning  of  the  boiler  and  any  subsequent  works  carried  out  on  the  appliance  must  be 

effected  by  a  suitably  trained  Gas  Safe  Registered  Technician.  The  BENCHMARK  record  for 
Commissioning and Annual Service at the back of this book should be completed. 

  The appliance must be used solely for the purpose for which it has been designed and manufactured: 

central heating and domestic hot water production. Any other use is deemed as improper and as such 
dangerous.  Under no circumstances will the manufacturer be held responsible for damage or injury to 
persons  or  animals  caused  by  errors  in  the  installation  and/or  use  of  the  appliance,  or  through  non-
compliance with current local and national standards and/or the manufacturer’s instructions.
 

  The  installation,  operation  and  maintenance  manual  form  an  integral  and  essential  part  of  the  product 

and must be kept near the appliance always. 

  This  Manufacturer  Installation  and  Maintenance  manual  must  not  be  removed  on  completion  of  the 

installation; must be kept in a safe place and made available for future reference. This Manual must be 
left along with the Benchmark commissioning booklet with the  boiler as Regulation 29 of the HSC Gas 
safety (installation and use) Regulations 1998

.

 

  The  warnings  contained  in  this  chapter  have  been  written  for  the  appliance  user,  the  installer  and  the 

service engineer. 

  The “operating instructions” chapter of this manual must be read carefully as it provides information on 

the operation and the operating limits of the appliance. 

  This appliance must be used exclusively in an un-vented central heating system. 

  After  the  removal  of  all  the  packaging,  check  that  the  appliance  has  not  been  damaged.  In  case  of  doubt,  do  not 

attempt to use the product but refer to the  supplier. Packing materials (cardboard box, wooden crate,  nails, staples, 
plastic bags, polystyrene, etc.) must not be left within reach of children in that these items represent a potential hazard 
and must be disposed of in a responsible manner. 

  Before  carrying  out  any  cleaning  or  maintenance  operations,  disconnect  the  appliance  from  the  mains  electricity 

supply by switching off at the main switch and/or any other isolating device. 

  Do not obstruct the air intake or flue exhaust grills. 

  Do not obstruct the air intake or flue exhaust terminals. 

  In the case of a fault and/or malfunction in the appliance, shut down the system. Do not interfere with or attempt any 

repairs. Call for professionally qualified technical assistance only. 

  Any repairs to the appliance under the manufacturers warranty must be carried out exclusively by the manufacturer’s 

authorised  technicians.  Non-compliance  with  this  requirement  may  compromise  the  safety  of  the  appliance  and 
invalidate  the  warranty.  In  order  to  guarantee  the  efficiency  of  the  appliance  and  its  correct  operation,  it  must  be 
serviced regularly by professionally qualified personnel in line with the manufacturer’s instructions. 

  When the appliance is no longer required for use, any parts that may constitute potential sources of danger must be 

rendered harmless. 

Содержание RKR 24



































































Отзывы: