background image

19724 MICROWAVE SENSOR FOR D10

Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. 
Call the Marketing Department at 888-RAB-1000 or email: [email protected]

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

.

19724 is used with a

120-277VAC 

dimmable driver and comes with a sensor antenna. Sensor is shipped with Factory Settings 

outlined below under 

DIP Switch Settings.

 If settings other than factory pre-sets are desired, the consumer may change DIP 

Switch Settings. For more detailed control of the sensor, the consumer can purchase MVSREM wireless commissioning tool 

(remote) to re-program sensor settings.

SPECIFICATIONS 

Sensor is not suitable for wet locations.

DIP Switch Settings 

Switch positions referred to as R for right position and L for left position when 
looking at sensor in orientation shown in Fig. 2, in which all switches are R.
See Fig. 1 and 2 for each setting’s corresponding switches. Setting options for 
each category are noted in (parenthesis) below. 

Factory Settings: 

designated in 

bold 

for each category

 

Detection Area:

 

 

 

Time Delay: 

how long lamp remains on at 100% after last 

recognized motion

•  100% (RR)
• 

75% (RL)

• 

50% (LR)

• 

10% (LL)

•  5s (RRR)
• 

30s (RRL)

• 

1min (RLR)

• 

5min (RLL)

• 

10min (LRR)

• 

20min (LRL)

• 

30min (LLL)

Fig. 2

Adjustable 

Detection Area

Time Delay

Daylight 

Sensor

Cut Off 

Period

Dim Level

Sensor 

Antenna 

Interface

+

-

0-10V

L’    N     N      L

DIP Switches

Daylight Sensor:

 

 

 

Cut Off Period: 

how long reduced light output lasts after 

time delay period before fixture switching off

 

 

 

 

 

 

Dim Level: 

light output level after time delay

•  Disabled (RR)
• 

5 fc (Daylight) (RL)

• 

1 fc (Twilight) (LR)

• 

.2 fc (Darkness) (LL)

• 

0s (RRR)

•  10s (RRL)
• 

1min (RLR)

• 

5min (RLL)

• 

10min (LRR)

• 

30min (LRL)

• 

1hr (LLR)

• 

Always (LLL)

•  10% (RR)
• 

20% (RL)

• 

30% (LR)

• 

50% (LL)

 L    R

DIP SWITCHES

Factory Settings shown below

L’ = driver

L = power source

Fig. 1

19724 Sensor

Antenna

Содержание HALV









Отзывы: