R-Tech I-CUT100P Скачать руководство пользователя

Страница: 10 / 17

This regulates the air pressure as displayed in gauge on front of machine. To adjust pressure pull

knob outwards and turn to adjust pressure, once correct pressure is obtained press knob inwards to

secure.

Operating machine

SAFETY PRECAUTIONS

WARNING!

ELECTRIC SHOCK CAN KILL

Do not touch electrically live parts or electrode with skin or wet clothing.

Insulate yourself from work and ground

Always wear dry insulating gloves

WARNING!

FUMES AND GASES can be dangerous

Keep your head out of fumes & gases produced from welding. Use ventilation or exhaust to remove
fumes & gases from breathing zone and general area.

WARNING!

WELDING SPARKS can cause fire or explosion

Keep flammable material away from work area. Do not weld on containers that have held combustibles

WARNING!

ARC RAYS can burn

Wear eye, ear and body protection Make sure work area is protected by proper shielding to avoid injury
to passers by.

Содержание I-CUT100P


















Результаты поиска

Содержание I-CUT100P

Отзывы:

Похожие инструкции для I-CUT100P

Бренды по названию

Популярные бренды

R-Tech I-CUT100P, Руководство по эксплуатации

Результаты поиска

Содержание I-CUT100P

Отзывы:

Похожие инструкции для I-CUT100P

Бренды по названию

Популярные бренды