Quincy QGS 40 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 132

Quincy QGS 40 Скачать руководство пользователя страница 81

Instruction book

2920 7101 22

81

Oil drain plugs

4. Collect the oil and deliver it to the local collection service. Refit and tighten the drain and vent plugs

after draining.
Re-tighten the top connection of the oil cooler.

5. Remove the oil filter (OF). Clean the seat on the manifold. Oil the gasket of the new filter and screw

it into place. Tighten firmly by hand.

6. Remove filler plug (FC).

Fill the air receiver/oil tank (AR) with oil until the level reaches the filler neck.
Take care that no dirt drops into the system. Refit and tighten filler plug (FC).

7. Run the compressor loaded for a few minutes. Stop the compressor and wait a few minutes to allow

the oil to settle.

8. Depressurise the system by unscrewing filler plug (FC) just one turn to permit any pressure in the

system to escape. Remove the plug.
Add oil, the oil level should be between the top of the sight glass (Gl) and the filling point (FC).
Tighten the filler plug.

9. Reset the service warning after carrying out all service actions in the relevant Service Plan: see

Service menu

.

7.3 Oil

separator

change

Warning

The operator must apply all relevant

Safety precautions

.

Procedure

1. Run the compressor until warm. Stop the compressor, close the air outlet valve and switch off the

voltage. Wait a few minutes and depressurize by unscrewing oil filler plug (FC) just one turn to
permit any pressure in the system to escape.

2. Remove the cover (Ac) from the air receiver/oil tank (AR) by unscrewing the bolts.

«
...
79
80
81
82
83
...
»

Содержание QGS 40





































































































































Отзывы:

Нет отзывов