Quincy QGS 40 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 132

Quincy QGS 40 Скачать руководство пользователя страница 104

Instruction book

102

2920 7101 22

10.1.2 Operation

Description

The compressor oil flow is controlled by two thermostatic valves (BV1 and BV2), ensuring reliable
compressor operation and optimum energy recovery.

Bypass valve (BV1) is integrated in the oil filter housing of the compressor and controls the oil flow
through the main oil cooler (Co) of the compressor. Bypass valve (BV2) controls the oil flow through the
oil/water heat exchanger (HE) of the ER unit. Both valves consist of an insert (thermostat) mounted in a
housing.

Flow diagram of compressor with energy recovery system

Reference

Designation

Reference

Designation

BV2

Thermostatic bypass valve of ER
unit

OF Oil

filter

HE

Oil/water heat exchanger (ER
unit)

AR

Oil separator vessel

E

Compressor element

BV1

Thermostatic bypass valve in oil
filter housing

Co Oil

cooler

(compressor)

Ca Aftercooler

(compressor)

1

Water inlet

2

Water outlet

BV2 starts closing the bypass line over the heat exchanger (HE) at the lower limit of its temperature range.
At the upper limit of its temperature range, the bypass line is completely closed and all the oil flows
through the ER heat exchanger.

«
...
102
103
104
105
106
...
»

Содержание QGS 40





































































































































Отзывы:

Нет отзывов