manualshive.com logo in svg

Quincy QGS 40, Инструкция, Страница: 117 / 132

Поделиться
Скачать
Quincy QGS 40 Скачать руководство пользователя страница 117

Instruction book 

2920 7101 22 

117

 

 

 

 

 

 

10.2.4.2 Before starting

 

 

 

Status icons for each compressor on the main screen of the master regulator. 

 

Icon

 

Status

 

Description

 

 

 

No valid compressor type

 

An unknown compressor type is detected 

 

 

No communication

 

Fixed Speed or VSD: No reply from the connected 
compressor within a time out. Electro pneumatic 
compressor: Status red from the compressor is not 
consistent or illogical. 

 

 

No answer

 

Connected compressor is not responding ( or not 
responding correctly) to the commands. (example: no 
reaction on a load command) 

 

 

Not available

 

Compressor is stopped and is counting out the Minimum 
Stop Time. During this time the compressor is Not 
Available to the ECOntrol6 algorithm. 

 

 

Shutdown

 

Compressor is in Shutdown condition 

 

 

Stopped / Running

 

The compressor is running local 

 

Input icons for each compressor on the main screen of the master regulator. 

 

Icon

 

Description

 

 

 

Frequency converter driven compressor 

 

 

Unload compressor 

 

 

Load compressor 

 

 

When the ECO6 is controlling the connected units, the icon is rotating 

 

 

10.2.4.3 Starting

 

 

 

After pressing the start button, the ECOi regulator will start, load, unload and stop the compressors needed 
to keep the net pressure between the programmed pressure bands, while taking into account the 
programmed ECOi parameters. 

Содержание QGS 40





































































































































Отзывы:

Нет отзывов