Page 13
Fast flash
Configured,
sensing
current data,
sensing
voltage data
Fast flash
Current and
volt logger
only…
Configured,
not sensing
valid data
Troubleshooting: Check installation
Time out:
5 minutes
LED diagnostics will remain ON for 5
minutes after the key is pressed
4.2.8 Data logger installation
Prior to installation make sure that data
loggers are configured using the Audit Wizard
feature at quincy.scadar.net.
Print and retain the audit configuration check
list before attending the audit location!
Download the audit configuration from
quincy.scadar.net to your EQ LTE™ base
station
Transfer the audit configuration from your EQ
LTE™ base station to each EQ LTE™ data
logger
Ensure that each data logger is installed to the
assigned audit location (e.g. air compressor
brand, model and or serial number or pressure
point)
4.2.9 EQ LTE™ current & volt data logger
4.2.9.1 Technical data:
Identification:
EQ LTE™ Logger, current & volts
2014900356
EQ LTE™
EQ LTE™ current & volts
data logger
Precision data logging
Part number:
Product family:
Definition:
Function:
Data logger:
A / D resolution:
16 bit
Battery life:
2 calendar years or more
(est.)
Bluetooth (slave):
2.1 + EDR (enhanced data
rate)
Bluetooth range:
10 meters (33 feet)
The effective range varies due to propagation
conditions, material coverage, production
sample variations, antenna configurations and
battery conditions
Operating temp:
0°C ~ +55°C (+32°F ~
+131°F)
Power / batteries:
Four AA lithium primary cells,
Li/SOCI2, 3.6V, 2700mAh
Real time clock:
Precision real time clock
(temp compensated crystal)
Maximum deviation:
0.4s / day
Sample capacity:
More than 1.4 million samples
(16 days continuous logging)
Sample frequency:
1 second (fixed resolution)
Software:
Pre-programmed application
software
Current sensor:
AC voltage:
Range: 100 V to 700 V
Accuracy: 1%
AC current:
Range: 10 Amp ~ 800Amp
Accuracy:
1%
Max nondestructive
current:
2000 A
Ambient temperature
influence on accuracy:
<0.1% per 1°C for
temperatures from -10°C to
+18°C and from 28°C to 50°C
Rise / fall time:
< 400ms
Burden resistance:
≤1 ohm
Operating temp:
-10°C ~ +50°C (+14°F ~
+122°F)
Storage temp:
-40°C to +70°C (-40°F to
+160°F)
Safety rating:
CAT III 600V
Useable frequency:
10Hz – 100 kHz
Dimensions:
216mm (8.5”) x 111mm (4.4”)
x 45mm (1.8”)
Jaw capacity:
52mm (2.05 inch)
Weight
0.65kg (1.4lb)
Conformity:
Drop test:
Mech and shock test:
IEC61010-031: 2008
IEC61010-1: 2010
IEC 68-2-32 @ 1 meter
IEC 68-2-27 @ 100G
Regulatory mark:
CE, UL
Volt measurement and test lead set:
Measuring device:
Alligator clip set (2)
Red & black pair of small,
insulated, nickel plate jaws
Blunt tip grabs round screw
heads up to 9.5mm
CAT IV 600V, CAT III 1000 V,
10A rating
Test lead set:
Red & black with safety
shrouded, standard diameter
banana plugs
Right angle connector on one
end and straight connector on
the other
Reinforced strain relief
1.5metre silicone-insulated
wire resists heat & cold
CAT IV 600V, CAT III 1000 V,
10A rating
Conformity:
EN 61010-1-032
73/23/EEC, Low voltage
(amended 93/68/EEC)
Regulatory mark
CE, UL
Содержание EQ LTE 2014900479
Страница 1: ...Equipment Technical Manual Base Station...
