Quincy Compressor QR-25 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

Quincy Compressor QR-25 Series Скачать руководство пользователя страница 30

QR-25 Series

Quincy Compressor

52201-105, May 2003

26

3501 Wismann Lane, Quincy IL - 62305-3116

Reversal of Compressor Rotation

Pressure lubricated QR-25 series compressors can be modified to operate in
reverse rotation with exception to the Models 206 & 210. These two models
operate in the counterclockwise direction only.

To reverse the operating direction of a pressure lubricated compressor,

perform the following steps:

Step 1)

Remove the control tubing from the hydraulic unloader and pilot
valve (if so equipped)...

the oil pressure gauge and hydraulic unloader...

the pilot mounting stud set screw and pilot valve assembly...

the oil filter

*

(turn counterclockwise)...

and six (6) oil pump housing bolts.

Step 2)

Rotate the oil pump housing

1

/

2

turn (180°). (Note: The rotational

arrow at the top of the pump housing should now reference the
direction you wish the compressor to rotate. (See

Fig. 5-4,

Compressor Directional Arrows

)

Step 3)

Re-install the six (6) housing bolts and torque them in a star or
cross pattern to six (6) ft.-lbs.

Step 4)

Remove the countersunk pipe plug

*

from the oil pump housing and

relocate it in the opposite (bottom) hole. (See

Fig. 5-5,

Relocating

Countersunk Pipe Plug

)

Failure to relocate this pipe plug will result in complete loss of oil flow

throughout the compressor. Compressor seizure will result and warranty
will be void. The countersunk pipe plug must always be relocated in the
bottom port position.

Step 5)

Install a new oil filter*. Tighten the filter

1

/

2

turn after initial gasket

contact.

Step 6)

Re-assemble the control components in reverse order.

Step 7)

Double check the directional arrows.

Step 8)

For aircooled models only, remove the standard compressor sheave
and replace with a reverse rotation sheave available from your
local Quincy Compressor Distributor.

Step 9)

Start the compressor and adjust the oil pressure.

Torquing Cylinder to Head Capscrews

Torque cylinder to head capscrews to specifications during assembly. Then,
run the compressor for at least 30 minutes. Shut the unit off and follow
precautions outlined in

SECTION 5,

Stopping for Maintenance.

Retorque

the head capscrews to same specifications while the unit is still hot.

Pix 1068

Fig. 5-4

Compressor Directional

Arrows

OIL RETURN PORT

FROM THE OIL FILTER

COUNTERSUNK

PIPE PLUG

OIL SUPPLY PORTS

TO THE OIL FILTER

Pix 1154

Fig. 5-5

Relocating

Countersunk Pipe Plug

*Not applicable to models without oil pumps.

«
...
28
29
30
31
32
...
»

Содержание QR-25 Series













































Отзывы:

Нет отзывов