background image

QR-25 Series

Quincy Compressor

52201-105, May 2003

8

3501 Wismann Lane, Quincy IL - 62305-3116

SECTION 3

SECTION 3

SECTION 3

SECTION 3

SECTION 3

INST

INST

INST

INST

INSTALLA

ALLA

ALLA

ALLA

ALLATION

TION

TION

TION

TION

                           Receiving Delivery

Immediately upon receipt of compressor equipment and prior to completely
uncrating, the following steps should be taken:

Step 1)

Inspect compressor equipment for damage that may have occurred
during shipment.  If any damage is found, demand an inspection
from the carrier.  Ask the carrier how to file a claim for shipping
damages.  (Refer to

 SECTION 3, 

Freight Damage 

 

for complete

details.) 

 Shipping damage is not covered by Quincy Com-

pressor warranty.

Step 2)

Insure that adequate lifting equipment is available for moving the
compressor equipment.

Improper lifting can result in component or system damage, or
personal injury.  Follow good shop practices and safety procedures
when moving the unit.

Step 3)

Read the compressor nameplate to verify the model and size
ordered.

Step 4)

Read the motor nameplate to be sure the motor is compatible with
your electrical conditions (volts, phase, hertz).

Step 5)

Read the pressure relief valve nameplate to be sure it does not
exceed the working pressure shown on the compressor or any other
component in the system.

Step 6)

Read and understand the safety precautions contained
within this manual.  

The successful and efficient operation of

compressor equipment depends largely upon the amount of care
taken to install and maintain the equipment. Quincy Compressor
strongly recommends that any or all person(s) in charge of install-
ing, maintaining, or servicing one of our compressors read and
understand the entire contents of this manual in order to perform
such duties safely and efficiently.

Freight Damage

It is extremely important that you examine every carton and crate as soon as
you receive it.  If there is any obvious damage to the shipping container, have
the delivering carrier sign the freight bill, noting the apparent damage, and
request a damage report.

If concealed damage is discovered at a later date, the carrier must

be notified within 15 days of initial receipt of freight. 

   

Concealed

shipping damage is not covered by Quincy Compressor Warranty.

Contact the carrier as soon as possible, giving them an opportunity to inspect
the shipment at the premises where the delivery was made.  Do not move the
damaged freight from the premises where the original delivery was made.

CAUTION !

Содержание QR-25 Series













































Отзывы: