Quest Engineering TELSEC MP2 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 58

Quest Engineering TELSEC MP2 Скачать руководство пользователя страница 7

Rev 1. 1 05/08/19

- 2 -

TELSEC

©

MP2 User Guide

2

Product Specifications

Specifications

Part number: 151052-32

▪

Inputs: 32 universal inputs supporting 0-5 VDC, 4-20 mA, thermistor & contact closure

▪

Outputs: 4 form C digital outputs. Contact rating: 0.5 A @ 60 VDC

▪

Network interface: Ethernet 10/100 Base-T

▪

Protocols supported: IPv6, IPv4, HTTP, HTTPS, DNP3, RADIUS Password Authentication, NTP,
SMTP (email), SNMP v1, v2c and v3 for Gets, Sets and traps/informs

▪

Serial interface: Two RS485 serial ports

▪

Serial Protocols Supported: DNP3, Modbus RTU read and write with up to 1024 (512 per port)
registers for 16 & 32-bit integers, floating point and signed integers

▪

Logging: Logs data for inputs, outputs, alarms and Modbus registers

▪

Alarm notification methods: email and SNMP traps or informs

▪

Alarm destinations: four programmable trap destinations, nine email addresses or distribution
lists

▪

I/O terminal: removable screw terminals supports up to 12 AWG wire

▪

Power: dual feed 24-48 VDC, 3.7 W max.

▪

Battery: long life lithium (PN 250034) 3 VDC*

▪

Ambient operating temperature: 23° to 131°F (-5° to 55°C), 0-95% RH

▪

Non-condensing

▪

Dimensions: 13.15 W x 4.15 L x 1.63 H in. (334 x 105 x 41 mm)

▪

Weight: 1 lb. (454 g)

▪

Warranty: 1 Year

*CAUTION - Battery may explode if mistreated.

Do not

recharge, disassemble or dispose of in fire.

Specifications subject to change without notice

«
...
5
6
7
8
9
...
»

Содержание TELSEC MP2



























































Отзывы:

Нет отзывов