Quest Engineering TELSEC MP2 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 58

Quest Engineering TELSEC MP2 Скачать руководство пользователя страница 32

Rev 1. 1 05/08/19

- 27 -

TELSEC

©

MP2 User Guide

8.3

Bypass Outputs

The bypass output page is used to turn on (activate) or off (deactivate) the outputs. Select a time
duration from the dropdown or the word FOREVER and then select the desired action of ON or OFF.
Outputs bypassed for a time period will return to automatic mode once the time elapses. Outputs
bypassed FOREVER must be manually returned to automatic by selecting Auto.

Figure 35 - Bypassing MP2 Outputs

8.4

User Administration

This page sets up the six available user names for the password and what areas the user can access. If
the RADIUS server function is enabled, then this option does not affect user access. The default
passwords are the same as the username, but in all lower case. No characters are displayed in the
password field for security reasons

Figure 36 - Webserver password setup

8.5

Advanced Settings

8.5.1

System Version & Update

Choosing the Advanced settings will display the current

version of the system’s firmware. Selecting the

Update button will cause the system to try and connect to an update server to look for upgrades. The IP
address used for upgrades must be accessible from the network the MP2 is on in order to perform the
upgrade. The IP address for the upgrade server is configured in the IP General window. See section

«
...
30
31
32
33
34
...
»

Содержание TELSEC MP2



























































Отзывы:

Нет отзывов