Quest Engineering SUPER ELF Скачать руководство пользователя страница 8

Страница: 8 / 56

4. OPERATION WITHOUT THE ROM MONITOR

A. Loading programs is done in the LOAD mode. If you have purchased

the address display option, the address just loaded will be displayed

along with the address contents. All loading must start at location 00

HEX.

(1) To load a program

a. Push RESET R key.

b. Push LOAD L key.

c. Push the 2 HEX keypad keys corresponding to the

contents or address 00 HEX.

d. Push the INPUT I switch.

e. The contents of address 00 HEX will be displayed by

the data displays.

f. Push the 2 HEX keypad keys corresponding to the

contents of the next address.

g. Push the INPUT I switch.

h. The contents of tat address will be displayed.

l. Repeat steps f and g until the entire program is

loaded.

(2) To make corrections.

a. Push RESET R key.

b. Push LOAD L key.

c. Push Memory Protect P key.

d. Push the INPUT I key until the preceding location is

reached.

e. Load the HEX keypad with the corrected data word.

f. Push the WAIT W key to enable memory writing.

g. Push the INPUT I key to load the correction data

word.

(3) To run programs.

a. Push the RESET R key.

b. Push the RUN G key. The program will start

executing at address 00 HEX.

Содержание SUPER ELF
























































Результаты поиска

Содержание SUPER ELF

Отзывы:

Quest Engineering SUPER ELF, Руководство пользователя, Страница: 8 / 56

Результаты поиска

Содержание SUPER ELF

Отзывы: