Quest Engineering SUPER ELF Скачать руководство пользователя страница 53

Страница: 53 / 56

( ) B. Install the capacitor. SOLDER.

( ) C. Install the resistor. SOLDER.

( ) D. Install the diode. SOLDER.

( ) E. Connect the two batteries in series with a short length of wire.

( ) F. Cut two 10 to 12 inch lengths of wire and connect the battery to the

PC board BAT connections. OBSERVE POLARITY. SOLDER.

( ) G. Cut the remaining wire into 4 equal lengths. Using two wires,

connect one pole of the two-pole slide switch to the PC board SW1

connections. SOLDER. Using the other two wires, connect the other

pole of the two-pole switch to the PC board SW2 connections.

SOLDER. NOTE: If the switch supplied has more than 4 terminals, be

sure that you wire up the switch as a two-pole single throw switch.

( ) H. On the front of the PC board out jumper J1 (near the right top side

of U45.

( ) K. This completes the memory saver option.

10. INITIAL CHECKOUT

The following steps will provide you with an orderly approach to

initial functional circuit verification. If you fail to obtain the proper

response, refer to the sections on troubleshooting and logic design. Or, if you

wish, return your SUPER ELF and we will replace any defective parts

without charge. Charges will be made for any parts damaged through

improper assembly, etc.
A.

Plug the transformer in and verify:

(1) The displays are lit.

(2) Only one mode LED is lit.

(3) Only one state LED is lit.

Push the RESET button and verify:

(1) The R LED is tit.

(2) The 1 LED is lit.

Push the LOAD button and verify:

(1) The L LED is lit.

(2) The 1 LED is lit.

Содержание SUPER ELF
























































Результаты поиска

Содержание SUPER ELF

Отзывы:

Quest Engineering SUPER ELF, Руководство пользователя, Страница: 53 / 56

Результаты поиска

Содержание SUPER ELF

Отзывы: