Quest Engineering SUPER ELF Скачать руководство пользователя страница 10

Страница: 10 / 56

(8) Continue to push the INPUT I key to step through the

memory contents one at a time.

(9) Push the RESET R key when completed.

NOTE: The contents of the monitor may be read out by using memory

location 00 in step 5.

To use the monitor to start execution of a program at any

location.

(1) Push the RESET R key.

(2) Push the HEX keypad key 0 twice.

(3) Push the Monitor M select key.

(4) Push the RUN G key and the data display will indicate 00.

(5) Push the two HEX keypad keys corresponding to the

starting address.

(6) Push the INPUT I key and the program will start

executing.

6. USING SINGLE STEP/SLOW STEP

The SUPER ELF has the ability to step through programs one

machine cycle at a time. Execution is halted at the negative edge of the TPA

signal in each machine cycle. At this point the CPU is in the process of

executing the current instruction cycle. The instruction set timing diagrams

in APPENDIX B should be consulted to determine the hardware state

corresponding' to the instruction being executed.

The single step/slow step mode may be entered from the RESET state

or the WAIT state by pushing the Single Step S key. Pro- gram execution

may then be started or resumed by pushing the RUN G key. A single push of

the RUN G key will advance the program one machine cycle. Holding the

RUN G key down will advance the program at a rate or approximately 1 to 2

machine cycles per second. Re- leasing the RUN G key will stop execution.

Pushing the WAIT W key disables the single step mode and then pushing

the RUN\ G key resumes normal speed operation.

Содержание SUPER ELF
























































Результаты поиска

Содержание SUPER ELF

Отзывы:

Quest Engineering SUPER ELF, Руководство пользователя, Страница: 10 / 56

Результаты поиска

Содержание SUPER ELF

Отзывы: