Quest Engineering SUPER ELF Скачать руководство пользователя страница 55

Страница: 55 / 56

Push the MEMORY PROTECT button and the INPUT button and

verify:

Location 0002 contains 23.

Push RESET, MONITOR SELECT, LOAD, and INPUT buttons in

that order and verify:

Location 0000 contains F8

Continue pushing the INPUT button to read out the contents of the

Monitor.

Push RESET, MONITOR SELECT, and SINGLE STEP buttons in

that order. Push the 0 button and then the 2 button. Then push the RUN

button but do not hold it in and verify:

(1) The W LED is lit.

(2) The 0 LED is lit.

(3) Location 0000 contains F8.

Push the RUN button but do not hold it in and verify:

(1) The W LED is lit.

(2) The 1 LED is lit.

(3) The address/data display shows 000120.

Push the RUN button again and verify:

(1) The W LED is lit.

(2) The D LED is lit.

(3) The address/data display shows 0002A1.

Push the RUN button again and verify:

(1) The W LED is lit.

(2) The 1 LED is lit.

(3) The address/data display shows XX2020 (where XX can be any

value and is CPU chip dependent).
V.

Push and hold the RUN button down and verify:

(1) After approximately one second, the CPU will cycle through

machine cycles at a rate of 1 to 2 per second.

(2) Shortly the displays will alternate between 000807 and 00073F.

This is the point in the MONITOR where the MONITOR is waiting for an

INPUT switch closure. At this point release the RUN button.
W. Push the WAIT button and then push the RUN button and verify:

(1) The display is either 00083F or 000807.

Содержание SUPER ELF
























































Результаты поиска

Содержание SUPER ELF

Отзывы:

Quest Engineering SUPER ELF, Руководство пользователя, Страница: 55 / 56

Результаты поиска

Содержание SUPER ELF

Отзывы: