Quest Engineering SUPER ELF Скачать руководство пользователя страница 49

Страница: 49 / 56

The following tools are not required but will be helpful if available.

An IC insertion tool.

A component lead bender.

A nut driver set.

Check the parts in the kit against the parts list to insure that the kit is

complete and to familiarize yourself with the parts. CAUTION: Do NOT

remove the integrated circuits from the antistatic (black) foam they were

shipped in until told to do so.

The printed circuit board is double-sided epoxy glass with plated

through holes. The front of the board has component designations on it. A1l

components are installed from the front and all soldering is on the back.

Carefully inspect both sides of the printed circuit board for shorts and

defects. The top of the board is more critical since the sockets, etc., cover up

the traces, and defects are harder to detect and correct. NOTE: Every board

is carefully inspected, under magnification, prior to shipment and the above

suggestion is a double check to minimize any inconvenience to you from

undetected defects. Any defects found are of course covered by our

warranty.

Referring to the component identification on the board and figure 2,

component layout, start assembly using the following steps. NOTE: If you

purchased options with your SUPER ELF, they can be added now or later.

We recommend adding them now by doing all corresponding steps at one

time. For example, install both the basic and optional sockets at the same

time. CAUTION: in each of the following steps, be sure that you have

installed the parts in the correct locations prior to soldering. This is

particularly important if you did not buy all the options since some locations

will be empty.

( ) A. Install low profile sockets for ICs U1 through U45 except for ICs

listed as optional. Note: Install a socket for U18 as part of the basic kit.

Slightly bend two leads on diagonally opposite corners to hold the

socket in place while you turn the board over. Solder these two pins

while the socket is

Содержание SUPER ELF
























































Результаты поиска

Содержание SUPER ELF

Отзывы:

Quest Engineering SUPER ELF, Руководство пользователя, Страница: 49 / 56

Результаты поиска

Содержание SUPER ELF

Отзывы: