manualshive.com logo in svg

Queensgate NANOSCAN NPC-D-6110, Руководство пользователя

Поделиться
Скачать
Queensgate NANOSCAN NPC-D-6110 Скачать руководство пользователя страница 12

E N - 0 1 4 6 3 5 - U M   R e v   2     N P C - D - 6 x x 0   N a n o M e c h a n i s m   C o n t r o l l e r   U s e r   M a n u a l         Page 12 of 34 

 

w w w . n a n o p o s i t i o n i n g . c o m                                                                                                                                                                            

3  Unpacking and Handling 

3.1 

Unpacking the NPC-D-6xx0 

 

 

 

 

Carefully  remove  the  product

’s  transit  packaging.  DO  NOT  remove  the  connector  protective 

covers until connections are to be made. Retain the transit packaging for possible future use. 

Visually  inspect  the system  for  transit damage  and  check  for  missing  items.  If  any  damage  or 

missing items are apparent do not attempt to install the system. 

If  the  system  is  damaged  in  any  way,  report  the  damage  to  the  manufacturer  and  return  the 

product using the returns procedure. If there are missing items, report them immediately to the 

supplier  (see  contact  details  at  the  end  of  this  document  and  refer  to  the  company  website 

www.queensgate.com). 

The contents of the NPC-D-6xx0 package are listed as follows: 

Table 3-1:  Contents of the NPC-D-6xx0 package 

ITEM 

QUANTITY 

Controller Specific 

NPC-D-6xx0 NanoMechanism Digital Controller 

(NPC-D6110, NPC-D-6220 or NPC-D-6330 

– depending upon order) 

1 

Power Supply 120W*  (Universal input with +24V dc output)  

1 

Mains IEC Power Supply Lead  

1 

Software (containing user manual, Controller Interface software and results 
file) 

1 

USB cable 

1 

NanoMechanism Stage extension cable(s) 

(optional) 

NanoMechanism Stage adaptor cable(s) 

(optional) 

*The NPC-D-6xx0 should only be used with supplied power supply. 

3.2 

Using the NPC-D-6xx0 

The NPC-D-6xx0 is a robust unit and requires no special handling precautions other than that 

normally followed with electronic equipment. 

 

Static  discharge  to  any  of  the  connectors  may  cause  damage,  so  ensure  that  all  personnel 

handling the unit are adequately grounded.  

 

The controller should not be subjected to mishandling or used in hostile environments. 

 

The  controller  is  a  free  standing  unit  and  should  be  located  on  any  stable  flat  surface  (e.g. 

workstation or a desk) providing protection against accidental damage.  

 

Do not obstruct the controller’s vents and cooling fan air flow as this may cause overheating. 

Содержание NANOSCAN NPC-D-6110



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды