The SSP-200/300 Enabler does not support automatic configuration of adapters upon insertion,
more commonly referred to as "Hot Swapping". This means the adapter must be installed in one
of the system's PCMCIA sockets before executing SSP231EN.EXE. If more than one adapter is
installed in a system, the Enabler must be executed separately for each adapter. Furthermore,
SSP231EN.EXE should be executed to release the resources used by the adapter before it is
removed from the PCMCIA socket. Since PCMCIA adapters do not retain their configuration
after removal, any adapter that is removed from the system must be reconfigured with the
Enabler after re-inserting it into a PCMCIA socket.
IMPORTANT:
The Enabler requires a region of high DOS memory when configuring
a SSP-200/300. This region is 1000H bytes (4KB) long and by default
begins at address D0000H (the default address may be changed using
the "W" option). If a memory manager such as EMM386, QEMM, or
386Max is installed on the system, this region of DOS memory must
be excluded from the memory manager's control. Consult the
documentation provided with the memory manager software for
instructions on how to exclude this memory region.
2.2.1 Command Line Options
To configure a SSP-200/300 in the system, the Enabler requires one command line argument
from the user to determine the configuration of the card. This argument must be enclosed in
parenthesis and within the argument, any or all of the following parameters may be specified
using a
comma (no spaces)
to separate each parameter:
S
socket
specifies which PCMCIA socket the SSP-200/300 must be inserted into for this
configuration argument to be used.
socket
must be in the range 0 - 15. This option is
required if the 'R' option is not used.
B
address
specifies the base I/O address of the SSP-200/300 in hexadecimal. This address
must reside on an even 8-byte boundary. This option is required if the 'R' option is
not used.
I
irq
specifies the interrupt level (IRQ) of the SSP-200/300 in decimal.
irq
must be one of
the following values: 3, 4, 5, 7, 9, 10, 11, 12, 14, 15, or 0 if no IRQ is desired. This
option is required if the 'R' option is not used.
W
address
specifies the base address of the memory window required to configure the
SSP-200/300. Set
address
= D0 for a memory window at segment D000,
address
=
D8 for a memory window at segment D800, etc. Valid settings for
address
are C8,
2-9
SSP-200/300 (Rev. I and later) User's Manual
Содержание SSP-200
