Quantum LTO-8 HH SAS Скачать руководство пользователя страница 71

Страница: 71 / 126

Chapter 4: Operations

Diagnostic and Maintenance Functions

QuantumLTO-8 HH SAS User’s Guide

Function Code L: Load/

Unload Test

Approximate Run Time = 30 seconds per loop
Total Number of Loops = 10

Function Code L

tests the drive's ability to load and unload a tape

cartridge.
Press the

Unload

button to stop the diagnostic and exit maintenance

mode. Pressing the

Unload

button once will abort the test at the end of

the current test loop. Pressing the

Unload

button twice will abort the

test immediately. Wait for the drive to rewind the tape and unload the
cartridge.

Caution:

Even though no data is written during this test, it is
recommended that you use a blank (scratch) cartridge for

this test.

Note:

If you inserted an invalid tape cartridge, error code

appears in the SCD. If you inserted a write-protected cartridge,
or the media has read-only compatibility, error code

appears

in the SCD. In either case, the tape drive unloads the cartridge

and exits Maintenance Mode after the cartridge is removed.

Place the drive in Maintenance Mode. For instructions, see

Entering

Maintenance Mode

on page 48.

Press the

Unload

button once per second until

appears in the

SCD. (If you cycle past the desired code, press the

Unload

button

once per second until the code reappears.)

Press and hold the

Unload

button for three or more seconds, then

release it to select the function. The SCD changes to a flashing

Insert a scratch (blank) data cartridge. The SCD changes to a
flashing

and the tape drive runs the tests.

• If no error is detected, the diagnostic will loop and begin again.

To stop the loop, press the

Unload

button for one second and

release. When the diagnostic ends,

temporarily appears in the

SCD, and the tape drive exits Maintenance Mode.

• If an error is detected, the

Fault

light flashes and the drive posts

an error code to the SCD. To determine the error, locate the
code in

Appendix A, Error Codes and Messages

. To clear the

error either turn the power off and then on again, or reboot the

Содержание LTO-8 HH SAS































































































































Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Похожие инструкции для LTO-8 HH SAS

Бренды по названию

Популярные бренды

Quantum LTO-8 HH SAS, Техническое справочное руководство

Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Похожие инструкции для LTO-8 HH SAS

Бренды по названию

Популярные бренды