manualshive.com logo in svg

Quantum LTO-8 HH SAS, Техническое справочное руководство

Поделиться
Скачать
Quantum LTO-8 HH SAS Скачать руководство пользователя страница 49

Chapter 4: Operations

Inserting a Tape Cartridge

QuantumLTO-8 HH SAS User’s Guide

41

Inserting a Tape Cartridge

To insert a tape cartridge:

1

Ensure that the drive is powered-on.

2

Ensure that the write-protect switch on the tape cartridge is 
properly set (see 

Write-Protect Switch

 on page 76).

Force a drive dump (part of the 
maintenance mode) 

Caution:

If the drive detects a permanent error and displays an 
error code, it automatically forces a drive dump (also 
known as a save of the firmware trace). If you force a 
drive dump, the existing dump will be overwritten 
and data will be lost. After you force a drive dump, 
do not turn off the power to the drive or you may 
lose the dump data. 

Choose one of the following procedures: 
• If the drive is in maintenance mode (

Ready

 light is flashing 

and 

Fault

 light is 

On

 for Maintenance mode), refer to 

Function Code 4: Force a Drive Dump

 on page 52. 

• If the drive is in operating mode (

Ready

 light is 

On

 or 

flashing), press and hold the 

Unload

 button for ten seconds. 

If captured dump data exists, the drive places it into a dump 
area (for information about retrieving the data, see 

Procedure 

1: Determining Firmware Level and Capturing Drive Dump

 on 

page 83).

Reset the drive 

Press and hold the 

Unload

 button until the drive begins the 

reset procedure (

Fault

 light will turn 

On

 when reset starts). 

Note:

If a tape cartridge is loaded in the drive the drive will 
unload the tape. Repeat the 

Reset the drive

 procedure 

after the tape is unloaded. The drive saves a dump of the 
current drive state, then reboots to allow 
communication. Do not cycle power as this will erase the 
contents of the dump.

Unload button Function 

How to Initiate the Function

Содержание LTO-8 HH SAS































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды