Qualitrol 118 Series Скачать руководство пользователя страница 4

Electronic Temperature Monitor 

E C N - 2 7 6 4 4  

3

 

J u l y   7 ,   2 0 1 0  

 

O

VERVIEW

 

QualiTROL Electronic Temperature Monitor

 

The Model 118 Electronic Temperature Monitor (ETM) can monitor up to 3 
thermocouples in ventilated dry type transformer windings, display the current 
winding temperatures and operate relays by comparing the highest of the 3 
winding temperatures to stored set point temperatures. 

The ETM provides the following standard features: 

 

Monitors 3 type K thermocouples. 

 

Displays each of the 3 thermocouple temperatures as well as the maximum 
temperature stored. 

 

Displays the channel that caused the stored maximum temperature. 

 

Operates a high contact rating SPST relay with fuse protected contacts to 
control Cooling fans. 

 

A Manual Fan Control provides the capability to force the Fans to turn ON. 

 

A Yellow LED Indicates that the Fans are ON. 

 

A Fan exerciser circuit will turn the Fans ON for a short time at periodic 
intervals (ON time and interval is programmable). 

 

Operates a relay with a SPDT contact when one of the inputs exceeds the 
ALARM setting. 

 

A RED LED indicates that the ALARM is ON 

 

An internal audible device (buzzer) sounds when alarm is ON. Audible can be 
silenced without changing state of Alarm Relay. 

 

The ALARM relay is normally energized so that ALARM is initiated on 
power failure. All other relays are normally de-energized. 

 

If a thermocouple goes open circuit, it is detected, the ALARM operates and 
the faulty channel displays “- - -“. A failed thermocouple will not cause a 
TRIP. 

 

Operates a relay with a SPDT contact when one of the inputs exceeds the 
TRIP setting. 

 

A RED LED indicates that the TRIP relay is ON 

 

A TEST function shows the stored set points, shows the internal temperature 
of the ETM, and tests the digital display, all LED’s and the buzzer.  

 

A 0 to 1 mA output is provided which is proportional to the highest of the 3 
input temperatures.  

 

An RS-232 data line is used to setup the programmable parameters of the 
unit. 

 

Prime Power can be jumpered to be 120 or 230/240 VAC 50/60Hz 

Courtesy of NationalSwitchgear.com

Содержание 118 Series
























Отзывы: