background image

QuadraTop

®

Complete Soft Top

for 2018-

 Current

4 Door Jeep

®

 Wrangler JLU

Item 

#

11113.2435

Loss of vehicle control involves risk of death or serious injury, particularly to 

parts of your body not restrained within vehicle. This product is intended for 

weather protection only and should not be relied upon to contain occupants 

in the event of an accident or to protect from either ground contact or falling 

objects. To reduce risk of accident or injury:

ALWAYS 

WEAR 

SEATBELTS

Always keep head, arms & body parts within vehicle.

Fully secure or stow the soft top before driving according to instructions.

Never try to latch or fold soft top while driving. Do not use if damaged or

worn.

Read and follow all instructions & warnings accompanying this product, in

your vehicle owner’s manual and Off Road Driving Supplement.

RISK OF EYE INJURY. Safety glasses should be worn at all times while install-

ing or maintaining this product.

PART LIST:

TOP DECK/HEADER AND REAR BOWS ASSEMBLY   QTY 1 

DRIVER SIDE QUARTER WINDOW 

        QTY 1  

PASSENGER SIDE QUARTER WINDOW

QTY 1

REAR WINDOW   

        QTY 1

CENTER BOW ASSEMBLY   

QTY 1

DRIVER SIDE DOOR SURROUND 

        QTY 1

PASSENGER SIDE DOOR SURROUND 

        QTY 1 

DOOR SURROUND RUBBER 

QTY 2

DOOR SURRUND SCREWS

        QTY 1 

REQUIRED TOOLS:

SAFETY GLASSES 

SOCKET WRENCH 

10MM SOCKET & DRIVER       

PHILLIPS HEAD SCREW DRIVER

This Replacement Top kit is designed to fit on your 4 Dr Jeep® Wrangler when 

the original soft top or hard top has been completely removed. Before begin-

ning your installation of this product, you will need to remove your existing soft 

top fabric, hardware or Hard top.

WARNING

CAUTION

NOTICE

DOOR  SURROND  KNOBS           

QTY  8                                                                                                 

TAILGATE BAR

QTY 2          

TAILGATE  BAR  CORNER  MOUNTS             

QTY  4                                                                                                         

CORNER MOUNTS SHORT KNOBS

QTY 8      

REAR  BOW  SCREWS  AND  NUTS             

QTY  4                                                                                              

REAR  BRACKET  SCREWS  &  NUTS             

  QTY  2                                           

REAR MAIN BRACKET SCREWS AND NUTS

QTY 2   

4MM ALLEN WRENCH

QTY 1

REAR MAIN BRACKET SCREW M8

QTY 4    

5MM ALLEN WRENCH

QTY 1

Содержание QuadraTop 11113.2435

















Отзывы: