Quadra-Fire SAPH-D-CSB-IPI Скачать руководство пользователя страница 47

Страница: 47 / 58

Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14

Optional Fan Installation

the gFK-160a fan has been designed to circulate room air

through the appliance to enhance heat output.
the gFK-160a system operates on 120 VaC, 60 hz power.

this is available through a receptacle in the factory installed

junction box on the underside of the appliance.
Compare CoNteNtS oF CaRtoN with the actual parts

received. If any parts are missing or damaged, contact your

dealer before starting installation.

WARNING! Risk of Fire!

Damaged parts could impair safe

operation.

DO NOT i

nstall damaged components.

the fan shall be installed by a qualified installer in accordance

with the installation instructions included with the fan kit.

Use the instructions below in regards to location of the fan

on the stove. For all other information, refer to instructions

included with the fan kit.
1. From the rear of the appliance, slide the fan into the fan

housing with the magnetic strips down, staggering the

gas line. the fan cord should be toward the inside of the

appliance. Bend tabs upward approximately 45 degrees.

See Figure 8.3.

Figure 8.3 Fan Housing

2. From the front of the appliance, plug the blower cord into

the junction box receptacle labeled “FaN.” Wrap the extra

cord inside the controls area in a manner so that it does

not contact the bottom of the firebox.

3. Slide temperature sensor switch/bracket assembly onto

the 10-32 screw located on the underside of the appliance.

Secure the bracket assembly with the wing nut provided.

See Figure 8.4.

wING NUT

Figure 8.4 Temperature Sensor Switch Installed

4. Remove the knob and locknut from the speed control.

Install speed control onto rear shroud with stem protruding

from pre-punched hole. attach the lock nut tightly and

reattach the knob on the stem. See Figure 8.5.

Figure 8.5 Pre-Punched Holes for Speed Control

Follow “Power Strip Style Junction Box” wiring diagram

section of gFK-160a installation instructions for wiring of

the fan.
Follow those instructions for all other information including

operation, maintenance and service parts.

HOLES FOR SPEED CONTROL

BEND TABS

Содержание SAPH-D-CSB-IPI



























































Результаты поиска

Содержание SAPH-D-CSB-IPI

Отзывы:

Похожие инструкции для SAPH-D-CSB-IPI

Бренды по названию

Популярные бренды

Quadra-Fire SAPH-D-CSB-IPI, Руководство по установке

Результаты поиска

Содержание SAPH-D-CSB-IPI

Отзывы:

Похожие инструкции для SAPH-D-CSB-IPI

Бренды по названию

Популярные бренды