Quadra-Fire SAPH-D-CSB-IPI Скачать руководство пользователя страница 3

Страница: 3 / 58

Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14

Installation Standard work Checklist

Customer:

Lot/Address:

Model (circle one): SAPH-MBK-IPI SAPH-MBK-IPIL

SAPH-D-PMH-IPI SAPH-D-PMH-IPI

SAPH-D-MBK-IPI SAPH-D-MBK-IPIL

SAPH-D-CSB-IPI SAPH-D- CSB-IPIL

Date Installed:

Location of Stove:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments:

Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed _____________________________________________________________________________________

_________________________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer) (Date)

Appliance Install

YES

IF NO, WHY?

Veriﬁ ed combustible or non-combustible clearances to walls. (Pg. 8)

___________________________

Stove is installed level. (Pg. 35)

___________________________

Venting/Chimney Section 7 (Pg 36-43)

Venting conﬁ guration complies with allowable vent requirements.

___________________________

Venting installed, locked and secured in place with proper clearance.

___________________________

Interior/Exterior ﬁ restops installed and sealed.

___________________________

Attic insulation shield installed.

___________________________

Exterior wall/Roof ﬂ ashing installed and sealed.

___________________________

Terminations/Roof ﬂ ashing installed and sealed.

___________________________

Electrical Section 8 (Pg 44-47)

Unswitched power (110-120 VAC) provided for the appliance.

___________________________

Switch wires properly installed.

___________________________

Gas Section 9 (Pg 48-49)

Appliance conﬁ guration matches fuel type.

___________________________

Was a conversion performed?

___________________________

Leak check performed and inlet/outlet pressure veriﬁ ed.

___________________________

Set air shutter for optimal ﬂ ame appearance.

___________________________

Appliance Setup Section 10 (Pg 50-52)

All packaging and protective materials are from removed inside/under/on

the appliance).

___________________________

Refractories, logs, and embers installed correctly.

___________________________

Glass assembly installed and secured.

___________________________

Accessories installed properly.

___________________________

Mesh, doors properly installed.

___________________________

Manual bag and all of its contents are removed from inside/under

the appliance and given to party responsible for use and operation.

___________________________

Started appliance and veriﬁ ed no

gas leaks exist.

___________________________

2343-982 Rev. B 2/14



= Contains updated information.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your ﬁ le.

• That this checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

WARNING! Risk of Fire or Explosion!

Failure to install appliance according to these instructions can

lead to a ﬁ re or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Содержание SAPH-D-CSB-IPI



























































Результаты поиска

Содержание SAPH-D-CSB-IPI

Отзывы:

Похожие инструкции для SAPH-D-CSB-IPI

Бренды по названию

Популярные бренды

Quadra-Fire SAPH-D-CSB-IPI, Руководство по установке

Результаты поиска

Содержание SAPH-D-CSB-IPI

Отзывы:

Похожие инструкции для SAPH-D-CSB-IPI

Бренды по названию

Популярные бренды