Q-Pumps QDB Series Скачать руководство пользователя | Manualshive

Страница: 7 / 24

background image

7

Assembly and installation manual

QIM/QDB Mixer Series

QIM/QDB-M01

ASSEMBLY PRELIMINARIES

Before beginning the assembly procedure identify every element that is going to be installed,

you can use the exploded view and part list shown in pages 8 and 9. During the assembly you

may need the following tools:

1. 1”, 3/4”, 9/16” and 1/2” Wrenches.

2. 3/16” and 1/4” Allen wrenches.

3. Rubber mallet.

4. Caliper or shims.

5. 5/8” & 7/8” Socket – for impeller nut.

6. 3/8” diameter steel rod – to hold stub shaft plus.

7. Torque Wrench

WARNING

Before servicing pump, disconnect electrical

power source, carefully relieve all pressure and

drain all fluids from pump and connected piping.

IN

ST

ALL
ATIO
N

«
...
5
6
7
8
9
...
»

Содержание QDB Series

























Отзывы:

Нет отзывов

Похожие инструкции для QDB Series

Бренд: Bailey Страницы: 103

Бренд: Tascam Страницы: 91

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 19

Balde Descarga 300

Бренд: Altrad Страницы: 13

Бренд: UNITED Страницы: 3

Mackie Control Universal Pro

Бренд: Mackie Страницы: 12

Strand Lighting 100 plus series

Бренд: Philips Страницы: 20

Бренд: H.Koenig Страницы: 56

Exodus Alpha MXR 1800

Бренд: Gecko Страницы: 26

Бренд: PEPCOOK Страницы: 32

Бренд: Denon Страницы: 28

Бренд: Gemini Страницы: 6

Бренд: Gemini Страницы: 12

Бренд: Azden Страницы: 4

Бренд: Azden Страницы: 4

Бренд: Continental Electric Страницы: 6

Бренд: Harrison Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды