PVR EU300F Скачать руководство пользователя страница 19

19

LI 4431.00 (IT-EN)

Operating and maintenance instructions

EN

8. Decommissioning

Drain the oil from the pump prior to the removal. 
If the oil is polluted, flush the pump with fresh oil (see “oil change”).
Drain the oil from the tank, plug the inlet and the discharge ports and store the pump 
without oil. 

9. Return for repair

In case of pump return for repair to PVR, provide a list of substances which have come 
in contact with the pump  and advise the risks involved in handling, if any. Drain the 
lubricant from the pump prior to shipping the pump back.

10. Disposal

Meaning of the “WEEE” logo found in labels
The following symbol is applied in accordance with the EC WEEE (Waste Electrical and 
Electronic Equipment) Directive.
This symbol (valid only in countries of the European Community) indicates that the 
product it applies to must NOT be disposed of together with ordinary domestic or 
industrial waste but must be sent to a differentiated waste collection system. 
The end user is therefore invited to contact the supplier of the device, whether the 
Parent Company or a retailer, to initiate the collection and disposal process after 
checking the contractual terms and conditions of sale.

Содержание EU300F























Отзывы: