Pumpex P 1001 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 22

Pumpex P 1001 Скачать руководство пользователя страница 6

SERVICE INSTRUCTION

P 601 - P 3001

P 601/701/801/1001/1501/2001/3001.58.0308.Eng/Digital

6 (22)

Complete overhaul

A complete overhaul of the pump should be carried out if there has

been water or oil in the motor housing, or if the pump has been in daily

operation for one year or 2000 operating hours. At low utilization the

pumps overhaul intervals can be extended.

Dismantle the pump completely, replace damaged and worn parts.

Clean all sealing surfaces and check that they are not damaged. If

water or oil has leaked into the motor housing, inspect and replace

ball bearings and shaft seals as required.

Warning

Prior to any work being carried out, always check that the pump is

disconnected from the power supply, and cannot be energized.

Dismantling

Loosen the bottom nuts/screws and remove the base plate. Unscrew

the nuts for the diffuser. Remove outer casing and diffuser with a crow

bar applied between diffuser and impeller nut. Pull out the diffuser

from the outer casing.

Unscrew the oil plug and drain the oil into a clean can and inspect it.

Check the oil. See

maintenance

of Shaft Seals.

«
...
4
5
6
7
8
...
»

Содержание P 1001























Отзывы:

Нет отзывов