Pumpex P 1001 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 22

Pumpex P 1001 Скачать руководство пользователя страница 12

SERVICE INSTRUCTION

P 601 - P 3001

P 601/701/801/1001/1501/2001/3001.58.0308.Eng/Digital

12 (22)

Note!!

Locate the holes for the terminal cables in the housing about 4

inches from the exit of the cable groups on the winding head.

When the housing has been mounted it may be cooled with compressed

air. When the housing has cooled down, the terminal cables can be

pulled up through the holes in the housing with a hook made of steel

wire. Mount the cable bushings (6-hole seals) on the two groups of

cables.

The thermal switches are connected in series and the connections

should be well insulated.

Assembly

Prior to assembly, clean all parts carefully, especially 0-ring grooves

and mating surfaces.

Grease or oil 0-rings to eliminate damage during assembly. Lubricate

screw threads to protect them and to simplify future disassembly.

Stator Unit, Contactor and Main Cover

Grease and mount the 0-ring in the upper bearing seat. Connect all

stator leads to the contactor according to wiring diagram and mount

the contactor at the bottom of the contactor chamber to the mounting

rail.

Grease and mount the 0-ring between stator unit and main cover.

Mount the main cover on the housing and tighten it against the stator

housing with the nuts. Check that the 0-ring or stator leads have not

been jammed.

«
...
10
11
12
13
14
...
»

Содержание P 1001























Отзывы:

Нет отзывов