Pumpex P 1001 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 22

Pumpex P 1001 Скачать руководство пользователя страница 13

SERVICE INSTRUCTION

P 601 - P 3001

P 601/701/801/1001/1501/2001/3001.58.0308.Eng/Digital

13 (22)

Cable Gland and Cover

Measure inner diameter of cable rubber bushing to see that it

corresponds to cable diameter. Place rubber bushing and washers

(one on each side of the bushing) on the cable.

Pull cable through the junction box cover, far enough to let the rubber

bushing seat on a non-deformed portion of the cable. Tighten the cable

gland body and the strain relief clamp.

Grease and mount the 0-ring in the cover. Connect the phase leads to

the contactor according to wiring diagram and screw the green ground

lead in the main cover.

Mount the cover on the main cover and arrange the leads so that they

are not jammed or block the functioning of the contactor. Tighten the

cover with the cap nuts.

Ball Bearings

Clean the oil casing and all sealing surfaces thoroughly. Remove burrs

and scratches. Pack the ball bearing up to 2/3 of its volume with a

ball bearing grease e.g. Shell Alvania Grease 3 or SKF Alfalub LGMT

3/1.

Mount the washer in the bottom of the bearing seat on the circlip.

Heat the bearing seat with LP-gas to about 150

o

C (340

o

F), and mount

the bearing in the seat. Mount the nilos ring and circlip on top of the

bearing.

Place the oil casing on a press with hole for the rotor shaft and

resting against the inner ring of the ball bearing. Place upper bearing

on the shaft and press both bearings into position against the shaft

shoulders.

Mount washer and circlip on the shaft below lower bearing. Turn the

rotor by hand and check that it turns freely without seizing.

Grease and mount the 0-ring between stator housing and oil casing,

put grease on the casing side. Slip the stator unit onto the rotor unit

and check that the 0-ring is not jammed or pinched. Tighten the stator

housing to the oil casing with the screws.

«
...
11
12
13
14
15
...
»

Содержание P 1001























Отзывы:

Нет отзывов