Pumpex P 1001 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

Pumpex P 1001 Скачать руководство пользователя страница 10

SERVICE INSTRUCTION

P 601 - P 3001

P 601/701/801/1001/1501/2001/3001.58.0308.Eng/Digital

10 (22)

Cover and Cable Gland

Unscrew the cap nuts for the cover. Lift off the cover and disconnect

the cable from the contactor (3-phase units only).

If water has penetrated through the cable gland, the cable seal should

be replaced. Remove strain relief clamp prior to unscrewing cable

gland body. Pull out cable, rubber bushing and washers.

NOTE!!

It is very important that the replacement parts be correctly

sized for the cable. Incorrect sizing can cause severe damage to the

pump.

Stator Unit with Contactor

Unscrew the nuts for main cover and remove the main cover from the

stator unit.

The motor insulation should always be tested in connection with

service or repair. Measure insulation resistance between the different

phase windings, between windings and ground, and between win-

dings and thermal switch circuit. The insulation resistance should be

measured with 500 V megohm-meter, and the reading should be at

least I megaohm. If the reading is lower, but not completely open,

drying the stator may recover usage of the motor.

If insulation resistance test shows motor open, the stator unit should

be rewound, or replaced.

«
...
8
9
10
11
12
...
»

Содержание P 1001























Отзывы:

Нет отзывов